Manuals / Heat & Glo LifeStyle / Household Appliance / Gas Heater

Heat & Glo LifeStyle GEM42 manual Service Parts, Log set assembly, NG, LP Exploded Parts Diagram

Models: GEM42

1 29

Page 4

Service Parts	GEM42

(NG, LP) Exploded Parts Diagram	Beginning Manufacturing Date: 7-02
(GN, PL) Vue éclatée des pièces	Ending Manufacturing Date: ______

5 Log set assembly

*Part number list on following page.

*La liste des numéros de pièce se trouve à la page suivante.

9	11	10
	11
		6
		6
	8	7

4	Heat & Glo • GEM42 • 371-900 Rev. N • 2/05

Page 4

Image 4

Heat & Glo LifeStyle GEM42 Service Parts, Log set assembly, NG, LP Exploded Parts Diagram, Beginning Manufacturing Date

Contents

Model Installers GuideGEM42 Underwriters Laboratories ListedSAFETY AND WARNING INFORMATION Due to the high temperature, the appliance shouldThis gas fireplace and vent assembly MUST be READ and UNDERSTAND all instructions carefullyTABLE OF CONTENTS Safety and Warning InformationService Parts Lists Section 3 Installing the FireplaceService Parts GEM425 Log set assembly NG, LP Exploded Parts DiagramGEM42 Service Parts List / Liste des pièces de rechangeACCESSORIES / ACCESSOIRES Valve Assembly Intermittent Pilot IgnitionService Parts NG, LP Exploded Parts DiagramInstallation Codes High Altitude Installations1Approvals and Codes Appliance CertificationPre-install Preparation 2Getting StartedIntroducing the Heat & Glo Gas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the GEM42 Heat & Glo GEM42 371-900 Rev. N 2/053Installing the Fireplace Constructing the Fireplace ChaseStep 1. Locating the Fireplace Fireplace Dimensions, LocationsStep 2. Framing the Fireplace Figure 3. Framing Dimensions47-1/2” 47-3/4”Heat & Glo GEM42 371-900 Rev. N 2/05 NOTE PIPES OVERLAP 1-1/4 INCHES AT EACH JOINTDVP90ST Step 3. Installing the Vent System A. Vent System ApprovalsTEMS OR COMPONENTS MAY BE USED Identifying Vent ComponentsPilot Shield Adjustment STRAIGHT UPFlue Restrictor Instructions VERTICAL VENTING V FT 40 MAX. 12.4 MVENTING WITH TWO 2 90 oELBOWS VENTING WITH ONE 1 90 ELBOWV FT H FTVENTING WITH THREE 3 90 ELBOWS V FTB. Installing Vent Components 3. Install Support BracketsVenting Out the Top Vent 1. Attach the First Vent Component to the Starting Collars4. Install Firestops Cut a 10-inch by 12-inch 254mm X 305mm hole through the wallFigure 15. 10 x 12 Hole and Vent Pipe Figure 16. Heat Shield, Interior & Exterior FirestopsC. Vent Termination Attic FirestopWARNING THE TERMINATION CAP MUST BE POSITIONED SO THAT THE ARROW IS POINT- ING UP= AREA WHERE TERMINAL IS NOT PERMITTED electrical servicenot to be installed above a gas meter/regulator assembly withinStep 4. Positioning, Leveling and Securing the Fireplace WARNING MAJOR U.S. BUILDING CODES SPECIFY MINIMUM CHIMNEY AND/ORFigure 22. Minimum Height from Roof to Lowest Discharge Opening Figure 23. Proper PositioningStep 5. Installing the Optional Heat-Out or Heat-Zone Kits Heat-Out KitHeat-Zone Kit Step 6 The Gas Control SystemStep 7. The Gas Supply Line Step 8. Gas Pressure RequirementsPressure Natural GasStep 9. Wiring the Fireplace Figure 26. Intermittent Pilot Ignition IPI Wiring DiagramIntermittent Pilot Ignition IPI Wiring 3 Volt Transformer Operation with Battery Back-upStep 10. Finishing Figure 27. Fan Wiring DiagramWARNING WHEN FINISHING THE FIREPLACE HIGH TEMPERATURE 300 0F / 149 0C MINIMPORTANT INSTALLATION NOTE Facing RequirementsFigure 31. Facing Template Dimensions Facing Thickness from 3/4” to 1-1/4”Step 11. Installing Trim, Logs and Ember Material Installing the TrimWARNING WHEN FINISHING THE FIREPLACE Figure 34. Glass AssemblyAfter the Installation Step 12. Before Lighting the FireplaceStep 13. Lighting the Fireplace Double-check for faulty componentsFireplace Maintenance 4Maintaining and Servicing Your FireplaceCleaning Flame Sensor Rod IPI Systems Frequency Annually Cleaning Glass Door

Service Parts

GEM42

(NG, LP) Exploded Parts Diagram

Beginning Manufacturing Date: 7-02

(GN, PL) Vue éclatée des pièces

Ending Manufacturing Date: ______

5 Log set assembly