Getting Started | Heat & Glo LifeStyle SL-750TV-IPI-E instruction

4	Getting Started	Installer Guide

A. Typical Appliance System

NOTICE: Illustrations and photos reﬂect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

NON-COMBUSTIBLE ROOF FLASHING MAINTAINS MINIMUM CLEARANCE AROUND PIPE

VENT PIPE (SECTIONS 7 and 8)

CEILING FIRESTOP ON FLOOR OF ATTIC (SECTION 8.B)

FRAMING/HEADER (SECTION 5)

VERTICAL TERMINATION CAP (SECTION 4.D)

STORM COLLAR (SECTION 4.D)

VENT PIPE PENETRATES ROOF

PREFERABLY WITHOUT AFFECTING

ROOF RAFTERS (SECTION 8.B)

ATTIC INSULATION SHIELD (NOT SHOWN) MUST BE USED HERE TO KEEP INSULATION AWAY

FROM VENT PIPE IF ATTIC IS INSULATED (SECTION 10.D)

FRAMING HEADED OFF IN CEILING JOISTS (SECTION 8.B)

OPTIONAL

WALL SWITCH

MANTEL AND MANTEL LEG (SECTION 5.D)

SURROUND

HEARTH EXTENSION

GAS LINE

(SECTION 11)

Figure 4.1 Typical System

16	Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. J • 12/09

Image 16

Heat & Glo LifeStyle SL-750TV-IPI-E, SL-950TV-IPI-E, SL-550TV-IPI-E owner manual Getting Started, Typical Appliance System

Contents

SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E What to do if you smell gas Congratulations Homeowner Reference Information Table of Contents User Guide Troubleshooting Appliance SetupReference Materials Limited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Appliance CertiﬁcationTempered Glass Speciﬁcations BTU Speciﬁcations High Altitude Installations Non-Combustible Materials SpeciﬁcationCombustible Materials Speciﬁcation Electrical Codes Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Decorative Doors and Fronts Lighting Instructions IPI Final inspection by Frequently Asked Questions After Fireplace is Lit Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote Control Maintenance Tasks-Qualiﬁed Service Technician Gasket Seal and Glass Assembly InspectionVenting Logs Either cobrahead or SIT Getting Started Typical Appliance System Tools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Negative Pressure Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase Clearances Mantel and Wall Projections Combustible Mantels Termination Locations Vent Termination Minimum Clearances Vent Guidelines Vent Information and DiagramsVent System Conﬁguration Vent Clearances and Framing Pipe Clearances to CombustiblesWall and Ceiling Penetration Framing Vertical Penetration Framing Installing Outside Air Kit Damper Assem- bly Appliance PreparationGas and Electrical Connections Securing and Leveling the Appliance Installing Vent Pipe Assembly of Vent SectionsInstall Attic Insulation Shield Securing Vent Sections Gas Information Fuel ConversionGas Pressure Gas Connection Wiring Requirements Optional Accessories RequirementsElectrical Information Code CSA C22.1 Ignition Module 3 VAC Transformer PLUG-IN Junction Box Installation Wall Switch Installation for Fan Optional Dimensions of Combustibles Finishing Noncombustible Facing Diagram Facing Material Appliance Setup Install the Log Assembly PIN Hole Install the Mesh Install Trim and/or SurroundInstall Hood Air Shutter Setting Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Ues to spark, and main Appliance Dimension Diagram Reference Materials Log Set Assembly Service Parts Service Parts List At Depot SL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E SL-950TV-IPI-E Stocked IPI Valve Assembly SL-550 / 750 / 950TV-IPI-E Contact Information