Heat & Glo LifeStyle SL-550TV-IPI-E, SL-950TV-IPI-E, SL-750TV-IPI-E

IGNITION

MODULE 3 VAC

TRANSFORMER 3V

PLUG-IN

	BLACK
RED	BROWN
RED

BLACK

BATTERY PACK

BROWN

INTERMITTENT

PILOT IGNITOR

I

S

WHITE

ORG

GROUND TO

FIREPLACE CHASSIS

ORG

GREEN

TEMP SENSOR	BLACK
	VALVE

THERMOSTAT WIRE ASSEMBLY

NOTE: 1. Ignition module, valve, pilot, and wall switch operate on 3 volts. 120 VAC is required at junction box unless equipped with battery back-up.

Figure 12.1 Intelliﬁre Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat

IGNITION

INTERMITTENT

PILOT IGNITOR

I

MODULE 3 VAC

S

TRANSFORMER 3V	WHITE
	ORG
	GROUND TO
PLUG-IN	FIREPLACE CHASSIS
BLACK

RED

BLACK

BATTERY PACK

PLUG IN

BROWN

BROWN

ORG

GREEN

TEMP SENSOR

BLACK

REMOTE RECEIVER

VALVE

NOTE: 1. Ignition module, valve, pilot, and wall switch operate on 3 volts. 120 VAC is required at junction box unless equipped with battery back-up.

Figure 12.2 Intelliﬁre Pilot Ignition (IPI) Wiring Diagram with Remote Receiver

Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. J • 12/09

29

Image 29

Heat & Glo LifeStyle SL-550TV-IPI-E, SL-950TV-IPI-E, SL-750TV-IPI-E owner manual Ignition Module 3 VAC Transformer PLUG-IN

Contents

What to do if you smell gas SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E Homeowner Reference Information Congratulations User Guide Table of Contents Reference Materials Appliance SetupTroubleshooting Limited Lifetime Warranty Limited Lifetime Warranty Appliance Certiﬁcation Listing and Code ApprovalsTempered Glass Speciﬁcations BTU Speciﬁcations Non-Combustible Materials Speciﬁcation High Altitude InstallationsCombustible Materials Speciﬁcation Electrical Codes Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Decorative Doors and Fronts Final inspection by Lighting Instructions IPI After Fireplace is Lit Frequently Asked Questions Maintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote Control Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualiﬁed Service TechnicianVenting Logs Either cobrahead or SIT Typical Appliance System Getting Started Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Negative Pressure Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase Combustible Mantels Mantel and Wall Projections Vent Termination Minimum Clearances Termination Locations Vent System Conﬁguration Vent Information and DiagramsVent Guidelines Pipe Clearances to Combustibles Vent Clearances and FramingWall and Ceiling Penetration Framing Vertical Penetration Framing Appliance Preparation Installing Outside Air Kit Damper Assem- blyGas and Electrical Connections Securing and Leveling the Appliance Assembly of Vent Sections Installing Vent PipeInstall Attic Insulation Shield Securing Vent Sections Fuel Conversion Gas InformationGas Pressure Gas Connection Optional Accessories Requirements Wiring RequirementsElectrical Information Code CSA C22.1 Ignition Module 3 VAC Transformer PLUG-IN Wall Switch Installation for Fan Optional Junction Box Installation Finishing Dimensions of Combustibles Facing Material Noncombustible Facing Diagram Appliance Setup Install the Log Assembly PIN Hole Install Trim and/or Surround Install the MeshInstall Hood Air Shutter Setting Intelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Reference Materials Appliance Dimension Diagram Service Parts Log Set Assembly At Depot Service Parts List SL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E Stocked SL-950TV-IPI-E SL-550 / 750 / 950TV-IPI-E IPI Valve Assembly Contact Information