Memory Board Slot Location | Hitachi 8880R manual

Figure 15 Memory Board Slot Location

Ch 1: Hardware

2A

15

10

7A

6A

11

14

3A

4A

13

12

5A

8A

9A

16

1A

1B

16

9B

8B

5B

12

13

4B

3B

14

11

6B

7B

10

15

2B

Connector

System Unit—Right Side

		Set A
	Memory	Front
	RiserBoard	Front
	RiserBoard	Side
		Side
		Set B

CPU

Memory Expansion Board #1

Memory Expansion Board #2

Memory Expansion Board #3 (optional)

Memory Expansion Board #4 (optional)

Figure 15 Memory Board Slot Location

The system supports the following specifications for memory DIMMs:

	Support DIMM	Description

	Memory DIMM 128MB DIMMs	SDRAM (SSTL interface, DIMM)
	256MB DIMMs	Buffer

	Error correction	ECC

16	Hitachi VisionBase 8880R Server

Image 20

Hitachi 8880R manual Memory Board Slot Location, The system supports the following specifications for memory DIMMs

Contents

Hitachi VisionBase 8880R Server Product Guide Copyright TrademarksDisclaimer Issue Date November Part Number 202-85031-01-Rev A Contents 3 Error Information POST Error System Beeps System Overview System Specifications1 Hardware 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Ch 1 Hardware Figure 2 Accessing the Power Supplies Powering-On the SystemFigure 1 Accessing the Power Supplies Figure 3 P/S Receptacle and On/Off Switch Front Panel Figure 4 Front Panel Detail Figure 6 Direct Boot Switch Detail Back PanelFigure 5 Back Panel Detail Detail A Removing the Server Panels and Accessing Its Components Safety GuidelinesWarnings and Cautions Tools and Supplies You Need Accessing the PCI Slots Figure 7 Accessing the Option Slots PCI/ISA Option Boards Figure 8 Option Slots Figure 9 Accessing the Hard Disk Drives Hard Disk DrivesSCSI SCA Hard Disk Drives Figure 10 Hard Disk Drive Bays Installing/Swapping a HDD Figure 11 Removing/Installing a HDD HDD HDD Position Pins HDD Carrier 4 Mounting Screws Optional DevicesFigure 12 Mounting the HDD Carrier Figure 14 CPU/VRM Installation Detail Figure 13 Memory and CPU Slots Memory Figure 15 Memory Board Slot Location The system supports the following specifications for memory DIMMs Jumper Settings Figure 16 System Board Default Jumper SettingsVRM #3 VRM #4 Figure 17 I/O Board Switch Settings Before Operations 2 System Environment SettingFlow of System Environment Setting What You Can Do with the System Environment Setting Outline of the Setup Menu Outline of ISA Configuration Utility ICU Setting for Each BoardNotes on Use PCI Board Setup Menu Flow of the Setup Menu Operation Starting the Setup Menu Figure 18 Entering Setup Menu Figure 19 Setup Menu Screen Configuration Setup Menu ScreenConfiguration of the Setup Menu Screen Operating the Keys on the Setup Menu In the Setup Menu, the following key operations are allowed Figure 20 Main Menu Screen Steps for Setting the Setup MenuWhat You Can Do on the Main Menu Primary Master Slave System Time and System DateLegacy Diskette A,B Reset Configuration Data Execute ROM Diagnostic UnsupportedWhat You Can Do on the Advanced Menu Network server PCI Configuration I/O Device ConfigurationSelect Resources Current Resources Parallel port Floppy disk controllerLocal Bus IDE adapter PS/2 Mouse Ext MP Configuration Table Enable memory gapConsole Redirection Unsupported I/O APIC Mode WinNT 4.0 Install Mode Large Disk Access Mode UnsupportedSpeaker Volume Caching Above 4GB Supervisor Password is User Password isSet Supervisor Password Set User Password Hard Drive IDE Hard Disk Drive What You Can Do on the Boot menuFigure 23 Boot Menu Screen What You Can Do on the Exit Menu Exit Saving ChangesExit Discarding Changes Figure 24 Exit Menu Screen ISA Configuration Utility ICU Notes on the Setup MenuLoad Setup Defaults Discard Changes Backup for ICU Disk Flow of Operation with the ICU System Resources Starting the ICUSpace Do not remove ICU DISK2 before the ICU terminates How to Use Help ICU ScreenOperating the ICU Figure 25 ICU Screen Exiting the ICU Checking Resource Status Checking Resources Used by the System Adding an Extended Board Checking Resources for Extended Boards 6. A dialog box for confirmation is displayed. Choose OK Reserving I/O Port Addresses Changing the Settings in Extended BoardsSettings for Each Resource Removing an Extended Board NOTE Unknown Card is displayed for RAID controller PC-CA7112 When ICU Program Disk Has Been DestroyedReserving Resources In Use from an ISA Board Restoring Configuration Information Lock/Unlock Card Errors and Countermeasures Restrictions on the ICU Returning the Settings to Defaults Returning the Settings of the Setup Information to DefaultsReturning the ICU Settings to Defaults List of Utility Settings Fixed Configuration Ch 2 System Environment Setting Symbios Logic SCSI Configuration Utilities This table defines the SCSI Select factory default settings 3 Error Information POST ErrorCh 3 Error Information Hitachi VisionBase 8880R System Beeps Installing Windows NT 2. Select Advanced Menu-Windows NT 4.0 Install Mode4 NT Drivers and Limitations Windows NT Driver Recommendations Ch 4 NT Drivers and Limitations Related Document 5 Related Document and SpecificationEnvironment Specification Ch 5 Related Document and Specification Hitachi VisionBase 8880R