Manuals / Hitachi / Computer Equipment / Server

Hitachi 8880R manual I/O Board Switch Settings, Ch 1 Hardware

Models: 8880R

1 62

Download 62 pages 10.5 Kb

Page 22

Image 22

Ch 1: Hardware

Below are the default switch settings for the I/O board, as shipped from the factory.

ISA #1 (Shared)
ISA #2				Riser
PCI #17		PCI #19		Riser
PCI #17		PCI #19		Connector
PCI #16	PCI #18		PCI #1	PCI #15

				DEC21152
						APIC	APIC	APIC	APIC
				PIIX4e
									DS1230	DS1230	uSMC
									NVRAM uSMC		uSMC
									NVRAM uSMC		Firmware
											Firmware
						Super I/O			BIOS
						PC87307			BIOS
						PC87307
											uSMC
				SW1	SW3	SW5					8. 8.
				SW2	SW4	SW6 SW7					8. 8.
											SEG1 SEG2
				SW1	SW3		SW5
LED5	LED3		LED1					ON
LED5	LED3		LED1					OFF
LED4		LED2								ON
										ON
-12V	+3.3V		+12V							OFF
-12V	+3.3V		+12V	1 2 3 4 5 6 7 8	1 2 3 4 5 6 7 8		1 2 3 4 5 6 7 8		1 2 3 4 5 6 7 8
-5V		+5V		SW2	SW4		SW6		SW7
				SW2	SW4		SW6		SW7

Figure 17 I/O Board Switch Settings

18	Hitachi VisionBase 8880R Server

Page 22

Image 22

Hitachi 8880R manual I/O Board Switch Settings, Ch 1 Hardware

Contents

Hitachi VisionBase 8880R Server Product GuideDisclaimer CopyrightTrademarks Issue Date November Part Number 202-85031-01-Rev AContents 3 Error Information POST Error System Beeps 1 Hardware System SpecificationsSystem Overview Ch 1 Hardware 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSICh 1 Hardware Hitachi VisionBase 8880R ServerFigure 1 Accessing the Power Supplies Powering-On the SystemFigure 2 Accessing the Power Supplies Figure 3 P/S Receptacle and On/Off Switch Front PanelFigure 4 Front Panel Detail Figure 5 Back Panel Detail Figure 6 Direct Boot Switch DetailBack Panel Detail AWarnings and Cautions Removing the Server Panels and Accessing Its ComponentsSafety Guidelines Tools and Supplies You NeedAccessing the PCI Slots Figure 7 Accessing the Option SlotsPCI/ISA Option Boards Figure 8 Option SlotsSCSI SCA Hard Disk Drives Figure 9 Accessing the Hard Disk DrivesHard Disk Drives Figure 10 Hard Disk Drive BaysInstalling/Swapping a HDD Figure 11 Removing/Installing a HDDHDD HDD Position Pins HDD Carrier 4 Mounting Screws Optional DevicesFigure 12 Mounting the HDD Carrier Ch 1 HardwareFigure 14 CPU/VRM Installation Detail Figure 13 Memory and CPU SlotsMemory Figure 15 Memory Board Slot Location The system supports the following specifications for memory DIMMsCh 1 Hardware Jumper SettingsFigure 16 System Board Default Jumper Settings Hitachi VisionBase 8880R ServerFigure 17 I/O Board Switch Settings Ch 1 HardwareFlow of System Environment Setting 2 System Environment SettingBefore Operations What You Can Do with the System Environment Setting Outline of the Setup MenuNotes on Use Outline of ISA Configuration Utility ICUSetting for Each Board PCI BoardSetup Menu Flow of the Setup Menu OperationStarting the Setup Menu Figure 18 Entering Setup MenuConfiguration of the Setup Menu Screen Setup Menu ScreenFigure 19 Setup Menu Screen Configuration Operating the Keys on the Setup Menu In the Setup Menu, the following key operations are allowedWhat You Can Do on the Main Menu Steps for Setting the Setup MenuFigure 20 Main Menu Screen Legacy Diskette A,B System Time and System DatePrimary Master Slave What You Can Do on the Advanced Menu Reset Configuration DataExecute ROM Diagnostic Unsupported Network serverSelect Resources PCI ConfigurationI/O Device Configuration Current ResourcesLocal Bus IDE adapter Parallel portFloppy disk controller PS/2 MouseConsole Redirection Unsupported Ext MP Configuration TableEnable memory gap I/O APIC ModeSpeaker Volume WinNT 4.0 Install ModeLarge Disk Access Mode Unsupported Caching Above 4GBSet Supervisor Password Supervisor Password isUser Password is Set User PasswordFigure 23 Boot Menu Screen What You Can Do on the Boot menuHard Drive IDE Hard Disk Drive Exit Discarding Changes What You Can Do on the Exit MenuExit Saving Changes Figure 24 Exit Menu ScreenLoad Setup Defaults ISA Configuration Utility ICUNotes on the Setup Menu Discard ChangesBackup for ICU Disk Flow of Operation with the ICUSpace System ResourcesStarting the ICU Starting the ICUOperating the ICU How to Use HelpICU Screen Figure 25 ICU ScreenExiting the ICU Checking Resource Status Checking Resources Used by the SystemAdding an Extended Board Checking Resources for Extended Boards6. A dialog box for confirmation is displayed. Choose OK Settings for Each Resource Changing the Settings in Extended BoardsReserving I/O Port Addresses Removing an Extended Board Reserving Resources In Use from an ISA Board When ICU Program Disk Has Been DestroyedNOTE Unknown Card is displayed for RAID controller PC-CA7112 Restoring Configuration Information Lock/Unlock CardErrors and Countermeasures Restrictions on the ICU Returning the ICU Settings to Defaults Returning the Settings to DefaultsReturning the Settings of the Setup Information to Defaults List of Utility SettingsCh 2 System Environment Setting Fixed ConfigurationHitachi VisionBase 8880R Server This table defines the SCSI Select factory default settings Symbios Logic SCSI Configuration UtilitiesCh 2 System Environment Setting Ch 3 Error Information 3 Error InformationPOST Error Hitachi VisionBase 8880RSystem Beeps 4 NT Drivers and Limitations Installing Windows NT2. Select Advanced Menu-Windows NT 4.0 Install Mode Windows NT Driver RecommendationsCh 4 NT Drivers and Limitations Hitachi VisionBase 8880REnvironment Specification 5 Related Document and SpecificationRelated Document Ch 5 Related Document and Specification Hitachi VisionBase 8880R