What You Can Do on the Security Menu | Hitachi 8880R specification

What You Can Do on the Security Menu

Ch 2: System Environment Setting

What You Can Do on the Security Menu

If you set a password in the Security menu, be sure to remember that password. Should you forget the password, the system equipment will become unusable, requiring some repair work. In such a case, consult the staff of the shop where you bought the system.

PhoenixBIOS Setup Utirity

Main	Advanced			Security	Boot	Exit
							Item Specific Help
Supervisor Password is :					Clear
Supervisor Password is :					Clear
User Password is :					Clear
Supervisor Password					[Enter]
User Password					[Enter]
Password on Boot :					[Disabled]

F1	Help	−↓	Select Item		-/+	Change Values	F9 Setup Defaults
ESC Exit		←→ Select Menu			Enter	Select Sub-Menu	F10 Save and Exit

Figure 22 Security Menu Screen

Supervisor Password is

When no password is set, “Clear” is displayed; when a password is set, “Enabled” is displayed.

User Password is

When no password is set, “Clear” is displayed; when a password is set, “Enabled” is displayed.

Set Supervisor Password

Used to set a supervisor password with 8 characters.

Set User Password

When a supervisor password is set, set a user password with 8 characters.

Password on boot

Specify whether or not to have the system prompt you to enter a password at startup.

•	Disabled:	No prompt for password entry
•	Enabled:	Prompt for password entry

Hitachi VisionBase 8880R Server

33

Image 37

Hitachi 8880R What You Can Do on the Security Menu, Supervisor Password is, User Password is, Set Supervisor Password

Contents

Product Guide Hitachi VisionBase 8880R Server Trademarks CopyrightDisclaimer Issue Date November Part Number 202-85031-01-Rev A Contents 3 Error Information POST Error System Beeps 1 Hardware System SpecificationsSystem Overview 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Hitachi VisionBase 8880R Server Figure 1 Accessing the Power Supplies Powering-On the SystemFigure 2 Accessing the Power Supplies Front Panel Figure 3 P/S Receptacle and On/Off Switch Figure 4 Front Panel Detail Back Panel Figure 6 Direct Boot Switch DetailFigure 5 Back Panel Detail Detail A Safety Guidelines Removing the Server Panels and Accessing Its ComponentsWarnings and Cautions Tools and Supplies You Need Figure 7 Accessing the Option Slots Accessing the PCI Slots Figure 8 Option Slots PCI/ISA Option Boards Hard Disk Drives Figure 9 Accessing the Hard Disk DrivesSCSI SCA Hard Disk Drives Figure 10 Hard Disk Drive Bays Figure 11 Removing/Installing a HDD Installing/Swapping a HDD Figure 12 Mounting the HDD Carrier Optional DevicesHDD HDD Position Pins HDD Carrier 4 Mounting Screws Figure 13 Memory and CPU Slots Figure 14 CPU/VRM Installation Detail Memory The system supports the following specifications for memory DIMMs Figure 15 Memory Board Slot Location Figure 16 System Board Default Jumper Settings Jumper SettingsVRM #3 VRM #4 Figure 17 I/O Board Switch Settings Flow of System Environment Setting 2 System Environment SettingBefore Operations Outline of the Setup Menu What You Can Do with the System Environment Setting Setting for Each Board Outline of ISA Configuration Utility ICUNotes on Use PCI Board Flow of the Setup Menu Operation Setup Menu Figure 18 Entering Setup Menu Starting the Setup Menu Configuration of the Setup Menu Screen Setup Menu ScreenFigure 19 Setup Menu Screen Configuration In the Setup Menu, the following key operations are allowed Operating the Keys on the Setup Menu What You Can Do on the Main Menu Steps for Setting the Setup MenuFigure 20 Main Menu Screen Legacy Diskette A,B System Time and System DatePrimary Master Slave Execute ROM Diagnostic Unsupported Reset Configuration DataWhat You Can Do on the Advanced Menu Network server I/O Device Configuration PCI ConfigurationSelect Resources Current Resources Floppy disk controller Parallel portLocal Bus IDE adapter PS/2 Mouse Enable memory gap Ext MP Configuration TableConsole Redirection Unsupported I/O APIC Mode Large Disk Access Mode Unsupported WinNT 4.0 Install ModeSpeaker Volume Caching Above 4GB User Password is Supervisor Password isSet Supervisor Password Set User Password Figure 23 Boot Menu Screen What You Can Do on the Boot menuHard Drive IDE Hard Disk Drive Exit Saving Changes What You Can Do on the Exit MenuExit Discarding Changes Figure 24 Exit Menu Screen Notes on the Setup Menu ISA Configuration Utility ICULoad Setup Defaults Discard Changes Flow of Operation with the ICU Backup for ICU Disk Starting the ICU System ResourcesSpace Do not remove ICU DISK2 before the ICU terminates ICU Screen How to Use HelpOperating the ICU Figure 25 ICU Screen Exiting the ICU Checking Resources Used by the System Checking Resource Status Checking Resources for Extended Boards Adding an Extended Board 6. A dialog box for confirmation is displayed. Choose OK Settings for Each Resource Changing the Settings in Extended BoardsReserving I/O Port Addresses Removing an Extended Board Reserving Resources In Use from an ISA Board When ICU Program Disk Has Been DestroyedNOTE Unknown Card is displayed for RAID controller PC-CA7112 Lock/Unlock Card Restoring Configuration Information Errors and Countermeasures Restrictions on the ICU Returning the Settings of the Setup Information to Defaults Returning the Settings to DefaultsReturning the ICU Settings to Defaults List of Utility Settings Ch 2 System Environment Setting Fixed Configuration This table defines the SCSI Select factory default settings Symbios Logic SCSI Configuration Utilities POST Error 3 Error InformationCh 3 Error Information Hitachi VisionBase 8880R System Beeps 2. Select Advanced Menu-Windows NT 4.0 Install Mode Installing Windows NT4 NT Drivers and Limitations Windows NT Driver Recommendations Hitachi VisionBase 8880R Environment Specification 5 Related Document and SpecificationRelated Document Hitachi VisionBase 8880R Ch 5 Related Document and Specification