Parallel port, Floppy disk controller, PS/2 Mouse | Hitachi 8880R

Parallel port

Ch 2: System Environment Setting

Parallel port

Used to make settings for the built-in parallel port. In ordinary circumstances, use the default settings.

•Parallel port Disabled Enabled (default)

•Mode

Output only (default) Bi-directional

EPP ECP

•Base I/O address 378 (default) 278

3BC

•Interrupt IRQ5

IRQ7 (default)

•DMA channel DMA1 DMA (default)

NOTE: The “DMA Channel” item is displayed when “ECP” is set in the “Mode” item.

Floppy disk controller

Used to make settings for the built-in floppy disk drive controller. In ordinary circumstances, use the default settings.

•Floppy disk controller Disabled

Enabled (default)

Local Bus IDE adapter

Used to make settings for the IDE controller. In ordinary circumstances, use the default settings.

•Local Bus IDE adapter Disabled

Enabled (default)

NOTE: Do not change the setting in “Local Bus IDE adapter” with the ICU.

PS/2 Mouse

Used to make settings for the mouse. In ordinary circumstances, use the default setting “Enabled”.

•PS/2 Mouse Disabled Enabled (default)

30	Hitachi VisionBase 8880R Server

Image 34

Hitachi 8880R manual Parallel port, Floppy disk controller, Local Bus IDE adapter, PS/2 Mouse

Contents

Hitachi VisionBase 8880R Server Product Guide Disclaimer CopyrightTrademarks Issue Date November Part Number 202-85031-01-Rev A Contents 3 Error Information POST Error System Beeps 1 Hardware System SpecificationsSystem Overview 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Ch 1 Hardware Figure 1 Accessing the Power Supplies Powering-On the SystemFigure 2 Accessing the Power Supplies Figure 3 P/S Receptacle and On/Off Switch Front Panel Figure 4 Front Panel Detail Figure 5 Back Panel Detail Figure 6 Direct Boot Switch DetailBack Panel Detail A Warnings and Cautions Removing the Server Panels and Accessing Its ComponentsSafety Guidelines Tools and Supplies You Need Accessing the PCI Slots Figure 7 Accessing the Option Slots PCI/ISA Option Boards Figure 8 Option Slots SCSI SCA Hard Disk Drives Figure 9 Accessing the Hard Disk DrivesHard Disk Drives Figure 10 Hard Disk Drive Bays Installing/Swapping a HDD Figure 11 Removing/Installing a HDD Figure 12 Mounting the HDD Carrier Optional DevicesHDD HDD Position Pins HDD Carrier 4 Mounting Screws Figure 14 CPU/VRM Installation Detail Figure 13 Memory and CPU Slots Memory Figure 15 Memory Board Slot Location The system supports the following specifications for memory DIMMs VRM #3 Jumper SettingsFigure 16 System Board Default Jumper Settings VRM #4 Figure 17 I/O Board Switch Settings Flow of System Environment Setting 2 System Environment SettingBefore Operations What You Can Do with the System Environment Setting Outline of the Setup Menu Notes on Use Outline of ISA Configuration Utility ICUSetting for Each Board PCI Board Setup Menu Flow of the Setup Menu Operation Starting the Setup Menu Figure 18 Entering Setup Menu Configuration of the Setup Menu Screen Setup Menu ScreenFigure 19 Setup Menu Screen Configuration Operating the Keys on the Setup Menu In the Setup Menu, the following key operations are allowed What You Can Do on the Main Menu Steps for Setting the Setup MenuFigure 20 Main Menu Screen Legacy Diskette A,B System Time and System DatePrimary Master Slave What You Can Do on the Advanced Menu Reset Configuration DataExecute ROM Diagnostic Unsupported Network server Select Resources PCI ConfigurationI/O Device Configuration Current Resources Local Bus IDE adapter Parallel portFloppy disk controller PS/2 Mouse Console Redirection Unsupported Ext MP Configuration TableEnable memory gap I/O APIC Mode Speaker Volume WinNT 4.0 Install ModeLarge Disk Access Mode Unsupported Caching Above 4GB Set Supervisor Password Supervisor Password isUser Password is Set User Password Figure 23 Boot Menu Screen What You Can Do on the Boot menuHard Drive IDE Hard Disk Drive Exit Discarding Changes What You Can Do on the Exit MenuExit Saving Changes Figure 24 Exit Menu Screen Load Setup Defaults ISA Configuration Utility ICUNotes on the Setup Menu Discard Changes Backup for ICU Disk Flow of Operation with the ICU Space System ResourcesStarting the ICU Do not remove ICU DISK2 before the ICU terminates Operating the ICU How to Use HelpICU Screen Figure 25 ICU Screen Exiting the ICU Checking Resource Status Checking Resources Used by the System Adding an Extended Board Checking Resources for Extended Boards 6. A dialog box for confirmation is displayed. Choose OK Settings for Each Resource Changing the Settings in Extended BoardsReserving I/O Port Addresses Removing an Extended Board Reserving Resources In Use from an ISA Board When ICU Program Disk Has Been DestroyedNOTE Unknown Card is displayed for RAID controller PC-CA7112 Restoring Configuration Information Lock/Unlock Card Errors and Countermeasures Restrictions on the ICU Returning the ICU Settings to Defaults Returning the Settings to DefaultsReturning the Settings of the Setup Information to Defaults List of Utility Settings Fixed Configuration Ch 2 System Environment Setting Symbios Logic SCSI Configuration Utilities This table defines the SCSI Select factory default settings Ch 3 Error Information 3 Error InformationPOST Error Hitachi VisionBase 8880R System Beeps 4 NT Drivers and Limitations Installing Windows NT2. Select Advanced Menu-Windows NT 4.0 Install Mode Windows NT Driver Recommendations Ch 4 NT Drivers and Limitations Environment Specification 5 Related Document and SpecificationRelated Document Ch 5 Related Document and Specification Hitachi VisionBase 8880R