Related Document and Specification | Hitachi 8880R instruction

5: Related Document and Specification

Ch 5: Related Document and Specification

5: Related Document and Specification

Related Document

•RAS and Support Document

Environment Specification

•

•

•

•

•

System Unit Specifications
Dimensions	[mm]
Height	756	(17U)
Depth	640
Width	430
Weight	70kg (175 lbs.)		to 100kg (250 lbs.)
No drives, 3 power supply, Maximum configuration
Input Requirements (per power supply)
Low range/High range
Rated Input Voltage	100 to 120 V		200 to 240 V
Rated Input Frequency	50–60 Hz		50–60 Hz
Rated Input Current	less than 10A
Power Supply Output Power (per power supply)
Low range/High range
Rated Steady-State Power
Maximum Peak Power	1,650 W (550W x (3 +1)
Temperature Range
Operating	5º–40º C
Shipping	-30º–60º C
Relative Humidity (non-condensing)
Operating	20%–80%
Non-operating	5%–100%

Maximum Wet Bulb Temperature

Hitachi VisionBase 8880R

57

Image 61

Hitachi 8880R manual Related Document and Specification, Environment Specification

Contents

Product Guide Hitachi VisionBase 8880R Server Trademarks CopyrightDisclaimer Issue Date November Part Number 202-85031-01-Rev A Contents 3 Error Information POST Error System Beeps 1 Hardware System SpecificationsSystem Overview 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Hitachi VisionBase 8880R Server Figure 1 Accessing the Power Supplies Powering-On the SystemFigure 2 Accessing the Power Supplies Front Panel Figure 3 P/S Receptacle and On/Off Switch Figure 4 Front Panel Detail Back Panel Figure 6 Direct Boot Switch DetailFigure 5 Back Panel Detail Detail A Safety Guidelines Removing the Server Panels and Accessing Its ComponentsWarnings and Cautions Tools and Supplies You Need Figure 7 Accessing the Option Slots Accessing the PCI Slots Figure 8 Option Slots PCI/ISA Option Boards Hard Disk Drives Figure 9 Accessing the Hard Disk DrivesSCSI SCA Hard Disk Drives Figure 10 Hard Disk Drive Bays Figure 11 Removing/Installing a HDD Installing/Swapping a HDD Figure 12 Mounting the HDD Carrier Optional DevicesHDD HDD Position Pins HDD Carrier 4 Mounting Screws Figure 13 Memory and CPU Slots Figure 14 CPU/VRM Installation Detail Memory The system supports the following specifications for memory DIMMs Figure 15 Memory Board Slot Location Figure 16 System Board Default Jumper Settings Jumper SettingsVRM #3 VRM #4 Figure 17 I/O Board Switch Settings Flow of System Environment Setting 2 System Environment SettingBefore Operations Outline of the Setup Menu What You Can Do with the System Environment Setting Setting for Each Board Outline of ISA Configuration Utility ICUNotes on Use PCI Board Flow of the Setup Menu Operation Setup Menu Figure 18 Entering Setup Menu Starting the Setup Menu Configuration of the Setup Menu Screen Setup Menu ScreenFigure 19 Setup Menu Screen Configuration In the Setup Menu, the following key operations are allowed Operating the Keys on the Setup Menu What You Can Do on the Main Menu Steps for Setting the Setup MenuFigure 20 Main Menu Screen Legacy Diskette A,B System Time and System DatePrimary Master Slave Execute ROM Diagnostic Unsupported Reset Configuration DataWhat You Can Do on the Advanced Menu Network server I/O Device Configuration PCI ConfigurationSelect Resources Current Resources Floppy disk controller Parallel portLocal Bus IDE adapter PS/2 Mouse Enable memory gap Ext MP Configuration TableConsole Redirection Unsupported I/O APIC Mode Large Disk Access Mode Unsupported WinNT 4.0 Install ModeSpeaker Volume Caching Above 4GB User Password is Supervisor Password isSet Supervisor Password Set User Password Figure 23 Boot Menu Screen What You Can Do on the Boot menuHard Drive IDE Hard Disk Drive Exit Saving Changes What You Can Do on the Exit MenuExit Discarding Changes Figure 24 Exit Menu Screen Notes on the Setup Menu ISA Configuration Utility ICULoad Setup Defaults Discard Changes Flow of Operation with the ICU Backup for ICU Disk Starting the ICU System ResourcesSpace Do not remove ICU DISK2 before the ICU terminates ICU Screen How to Use HelpOperating the ICU Figure 25 ICU Screen Exiting the ICU Checking Resources Used by the System Checking Resource Status Checking Resources for Extended Boards Adding an Extended Board 6. A dialog box for confirmation is displayed. Choose OK Settings for Each Resource Changing the Settings in Extended BoardsReserving I/O Port Addresses Removing an Extended Board Reserving Resources In Use from an ISA Board When ICU Program Disk Has Been DestroyedNOTE Unknown Card is displayed for RAID controller PC-CA7112 Lock/Unlock Card Restoring Configuration Information Errors and Countermeasures Restrictions on the ICU Returning the Settings of the Setup Information to Defaults Returning the Settings to DefaultsReturning the ICU Settings to Defaults List of Utility Settings Ch 2 System Environment Setting Fixed Configuration This table defines the SCSI Select factory default settings Symbios Logic SCSI Configuration Utilities POST Error 3 Error InformationCh 3 Error Information Hitachi VisionBase 8880R System Beeps 2. Select Advanced Menu-Windows NT 4.0 Install Mode Installing Windows NT4 NT Drivers and Limitations Windows NT Driver Recommendations Hitachi VisionBase 8880R Environment Specification 5 Related Document and SpecificationRelated Document Hitachi VisionBase 8880R Ch 5 Related Document and Specification