Operating the Keys on the Setup Menu | Hitachi 8880R guide

Image 29

Hitachi 8880R manual Operating the Keys on the Setup Menu, In the Setup Menu, the following key operations are allowed

Contents

Product Guide Hitachi VisionBase 8880R Server Trademarks CopyrightDisclaimer Issue Date November Part Number 202-85031-01-Rev A Contents 3 Error Information POST Error System Beeps System Overview System Specifications1 Hardware 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Hitachi VisionBase 8880R Server Figure 2 Accessing the Power Supplies Powering-On the SystemFigure 1 Accessing the Power Supplies Front Panel Figure 3 P/S Receptacle and On/Off Switch Figure 4 Front Panel Detail Back Panel Figure 6 Direct Boot Switch DetailFigure 5 Back Panel Detail Detail A Safety Guidelines Removing the Server Panels and Accessing Its ComponentsWarnings and Cautions Tools and Supplies You Need Figure 7 Accessing the Option Slots Accessing the PCI Slots Figure 8 Option Slots PCI/ISA Option Boards Hard Disk Drives Figure 9 Accessing the Hard Disk DrivesSCSI SCA Hard Disk Drives Figure 10 Hard Disk Drive Bays Figure 11 Removing/Installing a HDD Installing/Swapping a HDD HDD HDD Position Pins HDD Carrier 4 Mounting Screws Optional DevicesFigure 12 Mounting the HDD Carrier Figure 13 Memory and CPU Slots Figure 14 CPU/VRM Installation Detail Memory The system supports the following specifications for memory DIMMs Figure 15 Memory Board Slot Location Figure 16 System Board Default Jumper Settings Jumper SettingsVRM #3 VRM #4 Figure 17 I/O Board Switch Settings Before Operations 2 System Environment SettingFlow of System Environment Setting Outline of the Setup Menu What You Can Do with the System Environment Setting Setting for Each Board Outline of ISA Configuration Utility ICUNotes on Use PCI Board Flow of the Setup Menu Operation Setup Menu Figure 18 Entering Setup Menu Starting the Setup Menu Figure 19 Setup Menu Screen Configuration Setup Menu ScreenConfiguration of the Setup Menu Screen In the Setup Menu, the following key operations are allowed Operating the Keys on the Setup Menu Figure 20 Main Menu Screen Steps for Setting the Setup MenuWhat You Can Do on the Main Menu Primary Master Slave System Time and System DateLegacy Diskette A,B Execute ROM Diagnostic Unsupported Reset Configuration DataWhat You Can Do on the Advanced Menu Network server I/O Device Configuration PCI ConfigurationSelect Resources Current Resources Floppy disk controller Parallel portLocal Bus IDE adapter PS/2 Mouse Enable memory gap Ext MP Configuration TableConsole Redirection Unsupported I/O APIC Mode Large Disk Access Mode Unsupported WinNT 4.0 Install ModeSpeaker Volume Caching Above 4GB User Password is Supervisor Password isSet Supervisor Password Set User Password Hard Drive IDE Hard Disk Drive What You Can Do on the Boot menuFigure 23 Boot Menu Screen Exit Saving Changes What You Can Do on the Exit MenuExit Discarding Changes Figure 24 Exit Menu Screen Notes on the Setup Menu ISA Configuration Utility ICULoad Setup Defaults Discard Changes Flow of Operation with the ICU Backup for ICU Disk Starting the ICU System ResourcesSpace Do not remove ICU DISK2 before the ICU terminates ICU Screen How to Use HelpOperating the ICU Figure 25 ICU Screen Exiting the ICU Checking Resources Used by the System Checking Resource Status Checking Resources for Extended Boards Adding an Extended Board 6. A dialog box for confirmation is displayed. Choose OK Reserving I/O Port Addresses Changing the Settings in Extended BoardsSettings for Each Resource Removing an Extended Board NOTE Unknown Card is displayed for RAID controller PC-CA7112 When ICU Program Disk Has Been DestroyedReserving Resources In Use from an ISA Board Lock/Unlock Card Restoring Configuration Information Errors and Countermeasures Restrictions on the ICU Returning the Settings of the Setup Information to Defaults Returning the Settings to DefaultsReturning the ICU Settings to Defaults List of Utility Settings Ch 2 System Environment Setting Fixed Configuration This table defines the SCSI Select factory default settings Symbios Logic SCSI Configuration Utilities POST Error 3 Error InformationCh 3 Error Information Hitachi VisionBase 8880R System Beeps 2. Select Advanced Menu-Windows NT 4.0 Install Mode Installing Windows NT4 NT Drivers and Limitations Windows NT Driver Recommendations Hitachi VisionBase 8880R Related Document 5 Related Document and SpecificationEnvironment Specification Hitachi VisionBase 8880R Ch 5 Related Document and Specification