Manuals / Hitachi / Computer Equipment / Server

Hitachi 8880R manual A dialog box for confirmation is displayed. Choose OK

Models: 8880R

1 62

Download 62 pages 10.5 Kb

Page 47

6.A dialog box for confirmation is displayed. Choose [OK].

Ch 2: System Environment Setting

3.The [Card Category] list box like the one below is displayed. From the [Card Category] list box, select [Communication] and then choose [OK].

[ ]	Card Category

Select Card Category

Network

Mass Storage

Video

Communication

Multifunction

OK

Cancel

4.In the [Add Communication Card] dialog box, select [Communication Board] (or [HENKAN Board]), and then choose [OK]. A dialog box like the one below is displayed.

[	]	Add Communication Card
	Select Board:
	Communication board
	HENKAN Board
	Unlisted Card
	OK	Cancel	Advanced...	Help

5.If there is a conflict with resources in use, the following message then referring to “Chan ging the Settings in Extended Boards” on board already installed.

is displayed. In such a case, choose [OK], and page 44, change the settings for the extended

[ ]	ISA Configuration Utility

				OK
	This operation cannot be			OK
	This operation cannot be
	completed because of a
	resource conflict. One
	conflicting card is			Help
	conflicting card is
	Motherboard System Devices.
	The conflict with that card
	is Interrupt 4, but there
	may be other conflicts.

6.A dialog box for confirmation is displayed. Choose [OK].

7.The [Card Resource Usage] dialog box is displayed; record the contents of that dialog box, and then choose [Close].

8.The [ISA Configuration Utility] window is displayed. On that window, check that the extended board has been added.

9.From the File Menu, choose [Exit].

10.A message is displayed. Choosing [Yes] will save the system configuration data file “SYSTEM.IMG” into DISK2.

11.A termination message is displayed. Turn the power off.

12.Referring to the manual attached to the ISA board, change the setting for the extended board to the values recorded in step 7.

13.Install the extended board on the expansion slot (ISA). When you restart the system equipment, the extended board is usable.

NOTE: When you need to install an extended board in or remove it from the system equipment, call the maintenance personnel.

Built-in devices must be added or exchanged by maintenance personnel only. Be sure to avoid removing the cover and installing/removing built-in devices. Otherwise, operation of the equipment shall not be guaranteed.

Hitachi VisionBase 8880R Server

43

Image 47

Hitachi 8880R manual A dialog box for confirmation is displayed. Choose OK

Contents

Product Guide Hitachi VisionBase 8880R ServerIssue Date November Part Number 202-85031-01-Rev A CopyrightTrademarks DisclaimerContents 3 Error Information POST Error System Beeps System Overview System Specifications1 Hardware 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Ch 1 HardwareHitachi VisionBase 8880R Server Ch 1 HardwareFigure 2 Accessing the Power Supplies Powering-On the SystemFigure 1 Accessing the Power Supplies Front Panel Figure 3 P/S Receptacle and On/Off SwitchFigure 4 Front Panel Detail Detail A Figure 6 Direct Boot Switch DetailBack Panel Figure 5 Back Panel DetailTools and Supplies You Need Removing the Server Panels and Accessing Its ComponentsSafety Guidelines Warnings and CautionsFigure 7 Accessing the Option Slots Accessing the PCI SlotsFigure 8 Option Slots PCI/ISA Option BoardsFigure 10 Hard Disk Drive Bays Figure 9 Accessing the Hard Disk DrivesHard Disk Drives SCSI SCA Hard Disk DrivesFigure 11 Removing/Installing a HDD Installing/Swapping a HDDCh 1 Hardware Optional DevicesFigure 12 Mounting the HDD Carrier HDD HDD Position Pins HDD Carrier 4 Mounting ScrewsFigure 13 Memory and CPU Slots Figure 14 CPU/VRM Installation DetailMemory The system supports the following specifications for memory DIMMs Figure 15 Memory Board Slot LocationHitachi VisionBase 8880R Server Jumper SettingsFigure 16 System Board Default Jumper Settings Ch 1 HardwareCh 1 Hardware Figure 17 I/O Board Switch SettingsBefore Operations 2 System Environment SettingFlow of System Environment Setting Outline of the Setup Menu What You Can Do with the System Environment SettingPCI Board Outline of ISA Configuration Utility ICUSetting for Each Board Notes on UseFlow of the Setup Menu Operation Setup MenuFigure 18 Entering Setup Menu Starting the Setup MenuFigure 19 Setup Menu Screen Configuration Setup Menu ScreenConfiguration of the Setup Menu Screen In the Setup Menu, the following key operations are allowed Operating the Keys on the Setup MenuFigure 20 Main Menu Screen Steps for Setting the Setup MenuWhat You Can Do on the Main Menu Primary Master Slave System Time and System DateLegacy Diskette A,B Network server Reset Configuration DataExecute ROM Diagnostic Unsupported What You Can Do on the Advanced MenuCurrent Resources PCI ConfigurationI/O Device Configuration Select ResourcesPS/2 Mouse Parallel portFloppy disk controller Local Bus IDE adapterI/O APIC Mode Ext MP Configuration TableEnable memory gap Console Redirection UnsupportedCaching Above 4GB WinNT 4.0 Install ModeLarge Disk Access Mode Unsupported Speaker VolumeSet User Password Supervisor Password isUser Password is Set Supervisor PasswordHard Drive IDE Hard Disk Drive What You Can Do on the Boot menuFigure 23 Boot Menu Screen Figure 24 Exit Menu Screen What You Can Do on the Exit MenuExit Saving Changes Exit Discarding ChangesDiscard Changes ISA Configuration Utility ICUNotes on the Setup Menu Load Setup DefaultsFlow of Operation with the ICU Backup for ICU DiskStarting the ICU System ResourcesStarting the ICU SpaceFigure 25 ICU Screen How to Use HelpICU Screen Operating the ICUExiting the ICU Checking Resources Used by the System Checking Resource StatusChecking Resources for Extended Boards Adding an Extended Board6. A dialog box for confirmation is displayed. Choose OK Reserving I/O Port Addresses Changing the Settings in Extended BoardsSettings for Each Resource Removing an Extended Board NOTE Unknown Card is displayed for RAID controller PC-CA7112 When ICU Program Disk Has Been DestroyedReserving Resources In Use from an ISA Board Lock/Unlock Card Restoring Configuration InformationErrors and Countermeasures Restrictions on the ICU List of Utility Settings Returning the Settings to DefaultsReturning the Settings of the Setup Information to Defaults Returning the ICU Settings to DefaultsHitachi VisionBase 8880R Server Fixed ConfigurationCh 2 System Environment Setting Ch 2 System Environment Setting Symbios Logic SCSI Configuration UtilitiesThis table defines the SCSI Select factory default settings Hitachi VisionBase 8880R 3 Error InformationPOST Error Ch 3 Error InformationSystem Beeps Windows NT Driver Recommendations Installing Windows NT2. Select Advanced Menu-Windows NT 4.0 Install Mode 4 NT Drivers and LimitationsHitachi VisionBase 8880R Ch 4 NT Drivers and LimitationsRelated Document 5 Related Document and SpecificationEnvironment Specification Hitachi VisionBase 8880R Ch 5 Related Document and Specification