English

For miter cut setting

If the turntable has been set to either of the angles described, move the turntable adjusting side handle a little to the right and left to stabilize the position and to properly align the miter angle scale and the tip of the indicator before the operation starts.

For bevel cut setting

Move handle on bevel section to the right and left and check that the position is stable and that the bevel angle scale and the tip of the indicator are properly aligned. Then tighten the clamp lever.

Type of

To process crown molding at

 

To process crown molding at

 

 

positions 1 and 4 in Fig. 28.

 

positions 2 and 3 in Fig. 28.

 

 

Crown

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Molding

Miter Angle

Bevel Angle

 

 

 

 

 

 

Miter Angle

Bevel Angle

 

 

 

 

 

 

 

 

Setting

Setting

 

 

 

 

 

 

Setting

Setting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

45° Type

right 35.3°

left 30°

right 30°

left 35.3°

left 30°

right 30°

(

 

 

mark)

(

 

 

 

mark)

(

 

 

 

 

mark)

(

 

 

mark)

(

 

 

 

mark)

(

 

 

 

 

mark)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

38° Type

right 31.6°

left 33.9°

right 33.9°

left 31.6°

left 33.9°

right 33.9°

(

 

 

mark)

(

 

 

 

mark)

(

 

 

 

 

mark)

(

 

 

mark)

(

 

 

 

mark)

(

 

 

 

 

mark)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(1)Setting to cut crown moldings at positions q and r in Fig. 28 (see Fig. 29; tilt the head to the left): q Turn the turntable to the right and set the Miter Angle as follows:

* For 45°type crown moldings: 35.3° (

 

mark)

* For 38°type crown moldings: 31.6° (

 

mark)

 

wTilt the head to the left and set the Bevel Angle as follows:

*For 45°type crown moldings: 30° ( mark)

* For 38°type crown moldings: 33.9° ( mark)

ePosition the crown molding so that the upper surface (A in Fig. 27) contacts the fence as indicated in Fig. 30.

(2)Setting to cut crown moldings at positions w and e in Fig. 28 (see Fig. 31; tilt the head to the left): q Turn the turntable to the left and set the Miter Angle as follows:

* For 45°type crown moldings: 35.3° (

 

mark)

* For 38°type crown moldings: 31.6° (

 

mark)

 

wTilt the head to the left and set the Bevel Angle as follows:

*For 45°type crown moldings: 30° ( mark)

* For 38°type crown moldings: 33.9° ( mark)

ePosition the crown molding so that the lower surface (B in Fig. 27) contacts the fence as in Fig. 32.

 

 

 

Head

 

 

Head

 

 

 

 

 

Bevel Angle Scale

 

 

Bevel Angle Scale

 

 

 

 

 

 

 

 

q

 

 

 

w

e

 

r

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fence

Fence

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Base

 

 

 

Base

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Miter

Ang

le Scale

 

Turnt

able

Miter

An

gle Scale

Turnt

able

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 29

 

 

Fig. 31

 

 

Fence

 

 

 

Fence

 

 

A

 

B

B

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table on Base

 

 

Table on Base

 

 

 

Fig. 30

 

 

Fig. 32

 

 

20

Page 20
Image 20
Hitachi C12FSA instruction manual For miter cut setting, For bevel cut setting