Manuals / Hitachi / Computer Equipment / Projector

Hitachi CP-S845W Lamp continued, Replace the lamp with new one and, Reset the lamp time, English

Models: CP-S845W

1 34

Download 34 pages 52.32 Kb

Page 31

Lamp (continued)

Lamp (continued)

4	Replace the lamp with new one and
	fix it using the same two screws.	Screw
	• Firmly tighten the lamp screws. Loose screws may cause
	bad connection of the connector which in turn may result	Lamp
	in malfunctioning.	Lamp
	in malfunctioning.
5	Install the lamp cover and fix it using screws.
5	• To prevent burn, install the lamp cover and secure it using the screws.

• Do not turn on the power with lamp cover removed.

Lamp cover

Screw

•Whenever the lamp is replaced, reset the total operation time of the lamp. Do not reset if the lamp has not been replaced.

•Do not perform resetting without changing the lamp, as this can cause lamp breakage.

2. Reset the lamp time

If you have replaced the lamp after the lamp replacement time had expired, perform the procedure

explained below within 10 minutes after the power is turned on. The power will turn off automatically

when the 10-minute period expires.

	STANDBY/ON	MUTE
	FREEZE
	MAGNIFY VOLUME
	OFF
	POSITION ON	LASER
					STANDBY/ON
3					INPUT
3					MUTE
					MENU
	RESET	RIGHT			3
2	MENU ON	MOUSE ON			3
			1	1, 2	RESET
	BLANK	TIMER
	RGB	VIDEO

INPUT

ENGLISH

1)Press the RESET button on projector for 3 seconds or remote control TIMER button for 3 seconds and display the total lamp used time.

•When accumulated operation time of the lamp reaches 1500 hours, the following display will appear at the bottom of the screen.

2)Press the RESET button on projector or remote control MENU ON button during displaying the lamp used time.

3)Select the “0” on the screen using the MENU ( ) button or DISK PAD.

LAMP 1500 h

LAMP 1500		← 0		CANCEL

31

Image 31

Hitachi CP-S845W Lamp continued, Replace the lamp with new one and, fix it using the same two screws, Reset the lamp time

Contents

3 Compact size, light weight for portability 4 RGB output terminal FeaturesContents 2 High resolutionAbout Trademarks Instructions to Users 1 Video signal cables2 Power cord Before useDo not use power supplies other than that specified Safety precautionDo not look directly at the lens when the lamp is lit Do not install this unit in an unstable placeDo not stare directly into the laser aperture Be careful in handling the power cordENGLISH When you are not going to use for a long time CleaningHandle the power cord carefully Caution when carrying itCleaning the lens Caution when replacing the lampDo not place this unit where it gets hot VolumeNames and functions of each part Contents of shipping boxMain unit AC IN socket Remote control sensor MAIN POWER switchNames and functions of each part continued ENGLISHNames and functions of each part continued Remote control transmitterNames and functions of each part continued How to insert batteries1 Remove the battery the battery compartmentInstallation of liquid crystal projector InstallationExample of the projector and screen installation How to use foot adjustersPower on all connected equipment Turn the MAIN POWER switch of the projector on. I ONAdjust picture size using the projection lens ZOOM knob 5 Adjust focus using the projection lens FOCUS ringBasic operations continued To turn off the powerTurn the MAIN POWER switch of the projector off. OFF Install the lens capPress the MAGNIFY + button FREEZE FUNCTIONMAGNIFYING FUNCTION Press the FREEZE button3 Select the item to be adjusted using the MENU Adjustments and functionsTo return to the initial setting 2 Select the menu to be adjusted using the MENU2. Numerical display items V POSIT, H POSIT etc SET UPHow to use the SET UP menu 1. Bar display items VOLUME, BRIGHT etcDuring AUTO-adjustment Adjustments and functions continuedAUTO-adjustment AUTO-adjustment Confirm ScreenOPT. The menu OPT. allows you to control communication function etc Adjustments and functions continuedENGLISH IMAGE The menu IMAGE serves of the picture inversion2. Signal input terminal Connection to the video signal terminalsConnection to the RGB signal terminal 1. Input signal3. Example of computer signal Connection to the RGB signal terminalcontinuedENGLISH Connection to the RGB signal terminalcontinued 4. Initial set signalsENGLISH Connection to the control signal terminal1. Control signal terminal 2. Mouse emulationSerial mouse Connection to the control signal terminal continuedPS/2 mouse ADB Mac mouse3. Communication Connection to the control signal terminal continued4. Control command table Control command tableConnection to the control signal terminal continued Command dataThe procedure of default setting the Projector status Connection to the control signal terminal continuedThe procedure of getting the Projector status The procedure of setting the Projector statusAUDIO Example of system setupConnecting various equipment AUDIO IN2 Remove the front filter cover Cleaning the air filterClean the air filter using a vacuum cleaner Clean the air filter about every 100 hours3 Loosen two screws and pull the handle to remove the HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURELamp 2 Remove the lamp coverLamp continued fix it using the same two screwsInstall the lamp cover and fix it using screws 2. Reset the lamp timeMessage table Indicator displayOn-screen display Cause When you think something wrongENGLISH PhenomenaAll dimensions shown in inches Dimension diagram