Hitachi CPX960WE user manual Remote control transmitter, P button *2, Video RGB, Laser, Standby

Names and functions of each part (continued)

Remote control transmitter

Press to switch the input. (Refer to page 13, 19.)					VEOEO	Turns the laser beam on and off. Refer to page
VIDEO,	RGB		button _		_	LASER	button
						11 cocnerning usage and observe the cautions.
STANDBY		/	ON button	_	sTAN_B¥/oNPosmoN	POSITION button
Used to turn the power on and off.					$
					_	Pressingthetop, bottom,leftor rightof DiskPadafter
Press for 1 sec. or more to turn the power off
						pressing this button causes corresponding movement
(enter standby		status).
						(Effective only during RGB signal selection).
(Refer to pages13 and 14.)
$ DISK	PAD				_¢	RESET	MOUSE / RIGHT button
						(1)Operates as the RESET batten when the menu
(1) Used to select menu items when the menu
						is displayed. Press this button to return to the
screen is displayed (refer to page 16 - 18).
						initial	settings,
(2) When the menu is not displayed, the mouse
						(2)Used to click the right mouse button when the
shift function and left click function are active.
						menu is not displayed (refer to page 25,26).
*! (3)After	the		POSITION	button has been
					*!	(3)Pressing this button after scrolling the screen
pressed, the screen can be moved upward,
						with POSITION returns the screen to the original
downward		and		ght.

*MENU button

Used to turn the menu screen display on and off. (referto page 17 - 21).

¢ MAGNIFY button

Used to magnify the displayed =mage.

* P in P button *2

Used to turnP in P (Picture In Picture: displays sub video signal images in the RG8 signal) on and off.

Each time this button is pressed, operation will change in the following sequence:

button

Usedto turn thefreeze(still)imagedisplayon andoff.

VOLUME button

Adjusts the volume of the sound. Press [/\] to increase the volume and (_/) to decrease the volume. When there is no video signal input, operation is not possible when the input video signal is outside the sync range,

button

Applies Mute. (Press the Play button again to canceL)

(1)

(1)- (3) t

BLANK button

Used to turn blanking on and off. (Refer to page 20.)

FOCUS button

Used to adjust the focus of the image on the screen. (Refer to page 13.)

TIMER button

Turns the display of the time set with the Timer on the Menu screen on and off.

The timer is not displayed when no input signal is detected or when SYNC is out of range or during blanking or during freezing.

Refer to page 20, 21 concerning the method used to set the timer.

ZOOM button

Used to adjust the size of the image. (Refer to page 13.)

*AUTO button

Used to execute auto-adjust.*3

•These functions do not operate when initial screen message "NO INPUT IS DETECTED" or "SYNC IS OUT OF RANGE" is displayed.

*1 POSITION icon

When the POSITION button is pressed, the moving display icon wii[ appear at the bottom right of the screen.

While displaying the icon, you can operate POSITION.

*2

With the P in P function, signals are input to both RGB and VIDEO. This function operates only when the RGB signal has been selected. There is no display in the case of the no signal and

when the RGB signal is outside the sync range.

When P in P is used, audio is automatically switched to video.

in P in P, audio input can be switched by pressing the VOL /\and VOL _/keys of the remote control, displaying the audio bar and moving Disk Pad left and right during the display.

E_ _ RGB/VIDEO

*3 Auto adjustment function

The projector automatically adjusts 4 items (V. POSIT, H. POSIT, H. PHASE, H. SIZE).

When you choose AUTO (move the cursor to the right from the manual operation position), the AUTO confirmation menu shown below is indicated.

•Auto adjust requires several tens of seconds.

•Auto adjust may not operate correctly in some cases depending on the computer connected and the signal.

•Auto adjust may not operate correctly in some case: depending on the type of image.

•Execute auto adjust with the display of the applicafior being run by the computer at maximum.

•After auto adjust, the image may be slightly dark in some cases due to automatic adjustment of the signal level.

•Auto adjust canot execute when the initial display is "NO INPUT IS DETECTED" or "SYNC IS OUT OF

RANGE" during FREEZE or MAGNIFY.

10