Message table (continued)
Indicators
The POWER indicator, LAMP
POWER | LAMP | ||
indicator | indicator | ||
Lights orange | Turns | off | |
Flashes | green | Turns | off |
Lights | green | Turns | off |
Flashes | orange | Turns | off |
indicator and TEMP indicator light or blink in the following cases.
TEMP |
| Message | Processing | / | |
indicator |
| ||||
|
|
| |||
Turns | off | Standby | status |
| |
Turns | off | Warming | up |
| |
Turns | off | Operation | status ,1 |
|
|
Turns | off | Cool down |
|
| |
|
|
|
|
|
|
| Wait some time (approx. 20 min.) before | ||
Lights | red | Lights | red | Turns | off | The lamp does not light. *2 | turning the power on again, If the | ||
|
|
|
|
|
|
| indicator still lights, the lamp may have | ||
|
|
|
|
|
|
| failed and. Replace with a new lamp. | ||
Lights | red | Flashes | red | Turns | off | A lamp has not been inserted | Firmly insert the lamp as far as possible | ||
|
|
|
|
|
| or the lamp cover is missing, | and screw the lamp cover in place, | ||
Lights | red | Turns | off | Flashes | red | The coolingfan is notoperating. | Contact | your | dealer, |
Flashes | red | Flashes | red | Turns | off | The totallamp time has | Contact | your | dealer, |
|
|
|
|
|
| exceededthe replacementtime. |
|
|
|
When the LAMP e!' TEMP indicator lights or flashes, turn off the MAIN POWER switch before proceeding. If the problem still persists, contact your dealer or service company.
*1: When the cooling fan is stopped and the interior becomes overheated, the power will tam off automatically to allow cooling (the indicator will turn off). In such cases, turn offthe projector power, allow the set to cool and then tam the projector power on again. The lamp will then ligN. If the lamp does not light, contact your dealer or service company.
*2: In some cases, when the air holes becomes blocked and the interior temperature rises, the lamp will be turned off for protection and the LAMP iMicator will flash red. In such cases, turn offthe MAIN POWER switch, allow the set to cool (for approx. 20 min.) and then turn the power on again.
When you think something wrong
Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then
contact your dealer.
Symptom |
|
| Possible cause |
The power is not |
| ,The | main power switch is not turned on. |
turned on. |
| ,The | power cord is disconnected. |
No video or audio. | ,The | input is not correctly set. | |
|
| •No signal input. | |
Video is present | but | ,The | projector is not correctly connected. |
no audio. |
| ,The | volume is seet to minimum. |
|
| •Mute is turned on. | |
|
| •Audio is switched to Video when P in P is on. | |
Audio is present | but | ,The | projector is not correctly connected. |
no video. |
| ,The | brightness adjustment knob is rotated |
|
| fully | clockwise, |
|
| •The | lens cap is still on. |
Colorsare pale and | Color density and color matching are not | ||
colormatching is poor. | correctly adjusted. | ||
Images are dark. |
| ,Brightnessandcontrastare notcorrectlyadjusted. | |
|
| •The lamp is nearing the endof its servicelife. | |
Video is blurred. |
| Focus or H PHASE is out of adjustment. | |
The LAMP indicator | Lamp failure. | ||
lights red. |
|
|
|
The TEMP indicator | Internal overheating. | ||
lights red. |
|
|
|
|
| Remedy | Page |
,Tom on the main power switch. | P.13 | ||
,Plug the powercord into an AC poweroutlet. | P.9 | ||
,Use the | projector | or remote control to set. | P.8.10, |
|
|
| 13,19 |
,Connect | correctly. |
| P.9.31 |
,Connect | correctly. |
| P.9.31 |
,Press VOLUME + on the remote control or display | P.10.18 | ||
the menu screen and adjust the volume. |
| ||
,Press the MUTE button. | P.8.10 | ||
,DisplaystheVolumebarandswitchestheAudioinput. | P.10 | ||
,Connect | correctly. |
| P.9.31 |
,Select BRIGHT with the MENU button and then | P.17 | ||
press the (@) ) key. |
| ||
,Remove the lens cap. | P.13 | ||
Adjust the video. |
| P.18 | |
,Adjust the video. |
| P.18 | |
,Replace with a new lamp. | P.32 | ||
Adjust the focus or H PHASE. | P.13.18 | ||
Wait approximately | 20 min. and then turn the | P.33 | |
power on again. |
|
| |
,Make surethe ventilation openingsare notblocked. | P.31.32 | ||
,Clean the air filter. |
|
| |
•Lowertheambienttemperatureto 35degreesC orless. |
| ||
A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem.
33
