Hitachi GR2000-B Series Abbreviations

Hitachi Gigabit Router GR2000-B Series Quick Start Guide

iv GR2K-GA-0008

Rev. 1.00

Abbreviations

AAL ATM Adaptation Layer

ABR Available Bit Rate

AFI Authority and Format Indicator

AIS Alarm Indication Signal

ANSI American National Standards Institute

ARP Address Resolution Protocol

AS Autonomous System

ATM Asynchronous Transfer Mode

BECN Backward Explicit Congestion Notifica ti on

BGP Border Gateway Protocol

BGP4 Border Gateway Protocol 4

BGP4+ Multiprotocol Extensions for Border Gateway Protocol - ve rsion

4

BOD Bandwidth On Dem and

BPDU Bridge Protocol Data Unit

CATV Ca ble Television

CBR Constant Bit Rate

CIDR Classless Inter-Domain Routing

CIR Committ ed Information Rate

CLLM Consolidated Link Layer Management

CLNP Connectionless Network Protocol

CLP Cell Loss Priority

CRC Cyclic Redundancy Check

CR-LDP Constraint-Based Label Distribution Protocol

CSMA/CD Carrier Sense Multiple Access with Collision Detection

DA Destin ation Address

DCC Data Country Code

DCE Data Circuit terminating Equipment

DDP Datagram Delivery Protocol

DHCP Dynamic Host Configuration Protocol

DLCI Data Link Connection Identifier

DSAP Destination Service Access P oint

DSCP Differentiate Services Code Point

DSP Domain Specific Part

Contents

Main Statement on EN55022 Compliance Statement on Federal Communications Commission (FCC) Compliance Class A Emission Statement (Korea) Trademarks Release 1.00 (August 2002) Change Record Preface Abbreviations Page Page Page Page Safety Guide General Safety Guidelines ! DANGER: Specific Warning Instructions DANGER: Specific Caution Instructions ! Other Instructions Table of Contents Chapter 2 - Setup Process......... ............................................................. 2-1 Chapter 3 - Basic Operations ................................................. ................3-1 Chapter 4 - Troubleshooting ........................................ ......................... 4-1 List of Figures Chapter 4 - Troubleshooting ............................................................ ......4-1 Chapter 2 - Setup Process......... ............................................................. 2-1 Chapter 3 - Basic Operations ................................................. ................3-1 Page List of Tables Page Chapter 1 Introduction 1.1 Documents a bout the GR2000-B models Hitachi Gigabit Router GR2000-B Series Quick Start Guide 1-2 GR2K-GA-0008 Figure 1-1 Documentation for the GR2000-B Series Chapter 2 Setup Process 2.1 Check that All Necessary Components are Present 2.2 Assemble the Required Tools for Setup. 2.3 Setting Up the GR2000-B 2.3.1 The GR2000-1B * Note: For the details about connectors, indicators, and switches, see the GR2000-B 2.3.2 GR2000-2B * Note: For the details about connectors, indicators, and switches, see the GR2000-B 2.4 Dangers , Cautions, and Notes Regarding Setup ! 2.5 Installing the GR200 0-B on a Table or Desk * Note: Do not attach the rubber stoppers to the router when installing it into a rack. 2.6 Attachin g and Detaching the Power Cable * Note: When pulling a cable out of the connector, follow the procedures above in 2.7 Installing a Memory Card * Note: When inserting a memory card, the surface labeled with the part number Page ! 2.8 Software 2.9 The Setup Terminal and Cable Connections 2.9.1 Setup Terminal 2.9.2 Connecting Cable 2.9.3 Connecting a Setup Terminal to the GR2000-B 2.9.4 Connecting the GR2000-B to Other Devices * Note: The required type of cables differs depending on an interface you use. For cable 2.9.5 Turning the Power Switch ON ! 2.10 Normal Start-Up Process for the GR2000-B ! * Note: The STATUS RMP or STATUS ETHERNET indicator showing red indicates 2.10.1 Turning the Power OFF Page Chapter 3 Basic Operations 3.1 Configuration Exa mples 3.2 Startup of the GR2000-B 3.2.1 First-Time Login * Note: We strongly recommend that you set a password to secure the router. You can 3.2.2 Setting the Time GR2K-GA-0008 3-3 3.3 Setting the Configuration This section explains about how to configure the GR2000-B for operation. 3.3.2 Enter the Configuration Edit Mode (Begin Editing the Configuration) Here is some detailed information about the each of the settings. 3.3.1 Enter the Administrator Mode 3.3.3 Open the Configuration File * Note: his is the example for the case where the operative configuration file in memory 3.3.4 Set an IP Address for the Ethernet Port 3.3.5 Set a Default Route is opened. You can open any designated prepared configuration file by inputting the file name. 3.3.6 Check the Configuration You Set by Displaying its Information 3.3.7 Save the Configuration Information Into the Configuration File 3.3.8 Close the Configuration File 3.3.9 Return to the Administrator Mode 3-6 GR2K-GA-0008 3.3.10 Exit the Configuration Edit Mode (Finish Editing the Configuration) GR2K-GA-0008 3-7 3.4 Display of Operation Status 3.4.1 Display of the Operation Status Covering the Entire Router 3-8 GR2K-GA-0008 3.4.2 Display of the Operation Status of the Built-In Ethernet 3.4.3 Display of the Operation Status of the Interface Configured 3.4.4 Display of the Routing Table 3.5 More Details About Operation Page GR2K-GA-0008 4-1 Chapter 4 Troubleshooting 4.1 Troubleshooting for Operations Introduced in this Guide