Ilmi, GR2K-GA-0008 Rev | Hitachi GR2000-B Series manual

DSU	Digital Service Unit
DTE	Data Terminal Equipment
DVMRP	Distance Vector Multicast Routing Protocol
ELAN	Emulated LAN
ERP	Echo Response
ERQ	Echo Request
ES	End System
FCS	Frame Check Sequence
FDB	Filtering Data Base
FDDI	Fiber Distributed Data Interface
FEC	Forwarding Equivalence Class
FERF	Far End Receive Failure
GFR	Guaranteed Frame Rate
HDLC	High-level Data Link Control
HNA	Hitachi Network Architecture
ICMP	Internet Control Message Protocol
ICMPv5	Internet Control message protocol version6
IEEE	Institute of Electrical and Electronics Engineers, Inc.
IETF	the Internet Engineering Task Force
IDI	Initial Domain Identifier
IGMP	Internet Groupe Management Protocol
ILMI	Interim Local Management Interface
IP	Internet Protocol
IPv4	Internet protocolversion 4
IPv6	Internet Protocol version 6
IPv6cp	Ipv6 Control Protocol
IPX	Internetwork Packet Exchange
ISO	International Organization for Standardization
ISP	Internet Service Provider
ITU-T	International Telecommunication Union - Telecommunication,
	Standardization Sector
JDI	Japanese Domain Identifier
LAN	Local Area Network
LAPB	Link Access Procedure Balanced Mode
LCP	Link Control Protocol
LDP	Label Distribution Protocol

GR2K-GA-0008	v
Rev. 1.00

Image 5

Hitachi GR2000-B Series quick start Ilmi, GR2K-GA-0008 Rev

Contents

Hitachi Gigabit Router GR2000-B Series Rev Hitachi Gigabit Router GR2000-B Series Quick Start Guide Change Record Release 1.00 AugustPreface GR2K-GA-0008 Abbreviations GR2K-GA-0008 Rev Ilmi LEC PIM Viii Damage to the equipment or a disruption in service Safety GuideGeneral Safety Guidelines Specific Warning Instructions Specific Caution Instructions Other Instructions CleaningStorage Xii Table of Contents Display of Operation Status Xiv Documentation for the GR2000-B Series List of Figures Xvi List of Tables Xviii Documents about the GR2000-B models Chapter Introduction Documentation for the GR2000-B Series GR2K-GA-0008 Rev Check that All Necessary Components are Present Chapter Setup ProcessAssemble the Required Tools for Setup GR2000-1B Setting Up the GR2000-B 2 GR2000-2B Setup Process GR2000-2B Rear View GR2K-GA-0008 Rev Due to static electricity Front panel indicatorsTo yourself and the router Attaching the Rubber Feet Installing the GR2000-B on a Table or Desk Connecting a Power Cable to the GR2000-B Attaching and Detaching the Power Cable Installing a Memory Card Installing a Memory Card 10 After Installation of a Memory Card Permanently damage the memory card Software Setup Terminal Setup Terminal and Cable ConnectionsConnecting Cable Specifications Required for Setup Terminals Connecting the GR2000-B to Other Devices Connecting a Setup Terminal to the GR2000-B Turning the Power OFF Turning the Power Switch onMemory card, then power it on again Normal Start-Up Process for the GR2000-B This page left intentionally blank Chapter Basic Operations Configuration Examples Setting the Time First-Time LoginSet a password with passwd command Startup of the GR2000-B Basic Operations Setting the ConfigurationEnter the Administrator Mode Set an IP Address for the Ethernet Port Open the Configuration FileSet a Default Route Return to the Administrator Mode Close the Configuration File Manuals of the GR2000 Display of the Operation Status Covering the Entire Router Display of Operation Status Display of the Routing Table Display of the Operation Status of the Interface ConfiguredDisplay of the Operation Status of the Built-In Ethernet More Details About Operation Details About Other Settings This page left intentionally blank Types of Trouble and Corrective Action Chapter Troubleshooting Troubleshooting and Reference manuals More Details About Troubleshooting Troubleshooting