S11 Dtmf Tone Duration, S12 Escape Guard Time | Hitachi HPW-200EC

S11 - DTMF Tone Duration

Sets the duration of tones in DTMF dialing. This value has no effect on pulse dialing.

Range: 50-255 milliseconds

Default: 95 (95 milliseconds)

S12 - Escape Guard Time

Defines the guard time for the escape sequence, in fiftieths of a second.

Range: 0-255 1/50ths of a second

Default: 50 (1 second)

S36 - LAPM Failure Control

This value indicates what should happen upon a LAPM failure. If an invalid number is entered, the number is accepted into the register, but S36 will act as if the default value has been entered.

0=Modem disconnects

1=Modem stays on-line and a Normal mode connection is established

2=Modem stays on-line and a Normal mode connection is established

3=Modem stays on-line and a Normal mode connection is established

4=Modem disconnects

5, 6 =Reserved

7 =Modem stays on-line and a Normal mode connection is established (default)

S37 - Desired Line Connection Speed

This register specifies the desired line connection speed.

Default: 0

Desired line connection speed. This is interlinked with the Fn command . If an invalid number is entered, the number is accepted into the register, but S37 will act as if the default value has been entered.

0 = Attempt automode connection (default)

1-3 = Attempt to connect at 300bps. F1 command 4 = Reserved

5 = Attempt to connect at 1200bps. F4 command

6 = Attempt to connect at 2400bps. F5 command

7 = Attempt to connect at V.23. F3 command

8 = Attempt to connect at 4800bps. F6 command

9 = Attempt to connect at 9600bps. F8 command

10 = Attempt to connect at 12000bps. F9 command

11 = Attempt to connect at 14400bps. F10 command

12 = Attempt to connect at 7200bps. F7 command

13 = Attempt to connect at 16800bps

14 = Attempt to connect at 19200bps

15 = Attempt to connect at 21600bps

16 = Attempt to connect at 24000bps

17 = Attempt to connect at 26400bps

18 = Attempt to connect at 28800bps

20 = Attempt to connect at 33600bps

50

Image 51

Hitachi HPW-200EC manual S11 Dtmf Tone Duration, S12 Escape Guard Time, S36 Lapm Failure Control

Contents

Handheld PC Hardware Users Guide Information to Users ICES-003 Statement Important Safety InstructionsPage Page Page Industry Canada Terminal Equipment Statement Page Page MIC Welcome Picture from the Bottom of the Handheld PC Running your Handheld PC Batteries and power Operating your Handheld PC with the Main batteries To insert the rechargeable Li-ion battery pack To change the main battery Operating your Handheld PC with the AC adapter Charging rechargeable Li-ion battery pack Notification LED Using the stylus Pen Wireless infrared transferTo use the stylus Pen Left Side View of Handheld PC Interface cable PC card slot To insert a PC cardTo remove a PC card Using the CF card. also known as Compact Flash card To insert a CF cardTo remove a CF card To use a modem RAM/ROM Slot To change ROM board VGA Output Of Pocket PowerPoint Viewer Installation & Start-UpGeneral Description Usage ESC Using the Voice Recorder Page To assign application to User1 and User2 To use Quick Launch Key To decrease display contrast Adjusting the display contrastTo use and key To increase display contrast Resetting your Handheld PC To perform a simple resetTo perform a full reset Precautions Hardware SpecificationsPhysical Description and Features Weight Peripheral and Transfer Interface Power CF Card Compatibility PC Card Compatibility Data Compression Error CorrectionCompatibility Specification Standard Answer Re-execute CommandAT= x Write to Selected S-Register AT? Read Selected S-Register En Command Echo Dn DialDial Modifiers Mn Speaker Control Fn Select Modulation Compatibility onlyHn Disconnect and hook control Modem Identification Set Tone Dial Default On Return to On-Line Data ModeSet Pulse Dialing as a default Sn Access S-Register Xn Extended Result Codes Control RING, no CARRIER, ERROR, no DIALTONE, Connect Rate Summary of Supported Result Codes Cn DCD Data Carrier Detect Option Zn ResetFn Restore Default Configuration Yn Long Space Disconnect Kn Flow Control Mn Mode SelectionQn Mode Selection Gn Select Guard Tone \Nn Selects Operating Mode Display Current ConfigurationWn Store Current Configuration Yn Selects a Default Reset Profile 1.AT% Commands Enable/Disable Data Compression RingConnect 1200 Connect 75 Connect 1200 Busy Compression None Compression V.42bis S1 Ring Counter S0 Number of Rings to Auto-Answer S4 Line Feed Character S8 Pause Time For Dial DelayS2 Escape Character S3 Carriage Return Character S37 Desired Line Connection Speed S11 Dtmf Tone DurationS12 Escape Guard Time S36 Lapm Failure Control S83 EC Negotiation timeout S38 Delay Before Forced Hang Up Fax Modulation Table Value Modulation & Speed +FCLASS=n Select Service Class+Fcommand? Report Active Configuration +Fcommand=? Report Operating Capabilities +FTH=n Transmit Data with Hdlc Framing +FRS=n Receive Silence+FTM=n Transmit Data +FRM=n Receive DataPage Page HDECLARATION of Conformity Spring,1998