Horizon Fitness RC-40, RC-30 manual Introduction

INTRODUCTION

A S S E M B LY STEP 4

A S S E M B LY STEP 5

INTRODUCTION

IMPORTANT PRECAUTIONS

ASSEMBLY

STEP B

SEAT BASE

SEAT FRAME

WAVY WASHERS (G)

BOLTS (F)

STEP D

SEAT FRAMESEAT GUIDE RAILSEAT LEVER

SEAT LEVER CLAMP

SEAT GUIDE RAIL

SEAT LEVER CLAMP

NOTE: Be sure to keep SEAT LEVER positioned upward as shown. Orientate SEAT LEVER CLAMP with rounded edge facing away from SEAT GUIDE RAIL as shown above.

RECESS	EXPOSED WIRES
	LOWER HANDLEBAR
COVERED WIRE
	BOLTS (E)
	SPRING WASHERS (B)

	PULSE GRIP WIRES
WIRE CLIP	SEAT FRAME WIRES
RC-40 SHOWN

IMPORTANT PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

BIKE

OPERATION

CONDITIONING TROUBLESHOOTING LIMITED

GUIDELINES & MAINTENANCE WARRANTY

10

A.Open HARDWARE BAG FOR STEP 4.

B.Attach the SEAT BASE to the SEAT FRAME using 4 BOLTS (F) and 4 WAVY WASHERS (G).

C.Remove SEAT GUIDE RAIL CAPS, then remove the PRE-ATTACHED BOLTS, SPRING WASHERS and WASHERS from both ends of the SEAT GUIDE RAIL and lift from base frame. Note the orientation of the seat guide rail.

D.Slide the SEAT FRAME through the rear of the SEAT GUIDE RAIL as shown above. Lock SEAT FRAME into place by pusing down on SEAT LEVER. NOTE: Seat lever will face forward when in locked position.

E.Attach the RUBBER STOPPER to the bottom of the SEAT GUIDE RAIL using 1 SCREW (H).

F.Set assembled SEAT GUIDE RAIL on the grooves of the BASE FRAME.

G.Re-attach the PRE-ATTACHED BOLTS, SPRING WASHERS and WASHERS through the BASE FRAME into each end of the SEAT GUIDE RAIL. DO NOT TIGHTEN UNTIL ALL FOUR BOLTS HAVE BEEN STARTED.

H.Snap SEAT GUIDE RAIL CAPS back onto each end of SEAT GUIDE RAIL.

	SEAT GUIDE RAIL
PRE-ATTACHED WASHERS
PRE-ATTACHED SPRING WASHERS	CAP
PRE-ATTACHED BOLTS

SEAT GUIDE RAIL CAP

RUBBER STOPPER

SCREW (H)

BASE FRAME

HARDWARE BAG FOR STEP 4 CONTENTS :

BOLT (F)	WAVY WASHER (G)	SCREW (H)	RUBBER STOPPER
35 mm	18 mm	8 mm	Qty: 1
Qty: 4	Side View Qty: 4	Qty: 1

A) Open HARDWARE BAG FOR STEP 5.

B) Connect the SEAT FRAME WIRES to the PULSE GRIP WIRES as shown above.

C) Press COVERED WIRE into WIRE CLIP just before EXPOSED WIRES as shown above. Tuck EXPOSED WIRES under RECESS in LOWER HANDLEBAR.

D) Attach the LOWER HANDLEBAR to the SEAT FRAME using 4 BOLTS (E) and 4 SPRING WASHERS (B).

DO NOT PINCH WIRES!

E)Attach the SEAT BACK to the SEAT FRAME using 4 BOLTS (F) and 4 WAVY WASHERS (G).

SEAT BACK

WAVY WASHERS (G)

BOLTS (F)

RC-40 SHOWN

HARDWARE BAG FOR STEP 5 CONTENTS :

BOLT (E)	SPRING WASHER (B)	BOLT (F)	WAVY WASHER (G)
15 mm	15.4 mm	35 mm	18 mm
Qty: 4	Qty: 4	Qty: 4	Side View Qty: 4

11

BEFORE YOU BEGIN

BIKE OPERATION

LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES

RC-30_RC-40_Rev.1.3.indd 10-11 7/11/07 1:34:28 PM