Manuals / Brands / Power Tools / Welder / HP / Power Tools / Welder

HP 53A, E1351A HP E1351A/53A FET Multiplexer, Specifications, Appendix A, Humidity:, Watts/Slot:, Capacitance:, Cooling/Slot:, Maximum Voltage:, Number of Slots:

1 107

Download 107 pages, 1.54 Mb

Appendix A

HP E1351A/53A FET Multiplexer

Specifications

Maximum Voltage:	Screw Terminal Wire Size:	Watts/Slot: 1
Terminal to Chassis: ±16V peak*	16 AWG Max, 26 AWG Min
(input impedance less above 14V		Cooling/Slot:
peak)	Module Size/Device Type:	0.02 mm H2O @ 0.10 liter/sec
	B, register-based

	Maximum Current per Channel:
	1 mA (non-inductive)		Connectors Used: P1
	Maximum Offset Voltage:		Number of Slots: 1
	25 μV (0° to 28°C)
	250 μV (28° to 55°C)		Interrupt Level: selectable
			Interrupt Level: selectable
	Input Impedance:		Power Requirements:
	Power On (Vin <±10V)		Power Requirements:
	Power On (Vin <±10V)		Voltage:	+5V	+12V
	High to Low: >108Ω		Voltage:	+5V	+12V
	High to Low: >108Ω	>108Ω	Peak module
	High or Low to Chassis:		Peak module
	High or Low to Chassis:		current, IPM (A):	0.20	0.13
	Guard to Chassis: 10 kΩ ±10%		current, IPM (A):	0.20	0.13
	Guard to Chassis: 10 kΩ ±10%		Dynamic module
	Capacitance:		Dynamic module
	Capacitance:		current, IDM (A): 0.01		0.01
	High or Low to Chassis:	<200pf	current, IDM (A): 0.01		0.01
	High or Low to Chassis:	<200pf

High to Low: <200pf

		Strain Gage Excitation:
	Power Off (High to Low):	+ 4.63V ±10%
	Power Off (High to Low):	Max Current: 400mA
	for Vin ≤14V: 1000Ω	Max Current: 400mA
	for Vin ≤14V: 1000Ω	(short circuit protected)
	for Vin >14V: 220Ω	(short circuit protected)
	for Vin >14V: 220Ω
	Closed Channel Resistance:	Reference Junction Measurement
	Closed Channel Resistance:	Accuracy (HP E1353A only): 0.3°C
	<3.1 kΩ for high or low input	Accuracy (HP E1353A only): 0.3°C
	<3.1 kΩ for high or low input	(over 18° to 28°C operating temperature)
	(Guard not switched)	(over 18° to 28°C operating temperature)
	(Guard not switched)
	Bandwidth (-3dB):
	50Ω source, 1 MΩ 10pF
	termination: >200 kHz

*Each FET is diode clamped to ±14V and a 220Ω series resistor. This limits the current to the clamp diodes.

Humidity: 65% 0° to 40°C

Operating Temperature: 0° to 55°CStorage Temperature:

-40°to 75°C

EMC, RFI, Safety:

meets FTZ 1046/1984, CSA 556B, IEC 348, UL 1244

Net Weight (kg): 0.9

Appendix A

HP E1351A/53A FET Multiplexer Specifications 79

Contents

Contents Page Page Page Page Page July 20 Page Reader Comment Sheet BUSINESS REPLY MAIL HEWLETT-PACKARDCOMPANY Page Getting Started with the HP E1351A/53A Using This Chapter FET Multiplexer Module Description Multimeter Connection Points Analog Bus Connector Page Switchbox and Scanning Voltmeter Configurations Digital Bus and Triggering Programming Language Initial Operation Configuring the HP E1351A/53A FET Multiplexer Modules Warnings and Cautions Multiplexer Card Numbers Setting the Address Switch Selecting the Interrupt Line Number Setting the Card ID Switch Connecting User Inputs Adding Signal Conditioning Components/Current Shunts Connecting Field Wiring Wiring a Terminal Module Connecting Multimeters and Signal Generators Analog Bus and Digital Bus Cables Page Using the HP E1351A/53A FET Multiplexer Modules Selecting Channels Page Multiplexer Commands Connecting Switchbox Channels to Direct Terminals Comments Connecting Switchbox Channels to Tree Terminals for Making Measurements Page Scanning a Range of Switchbox Channels Page Example: Making 2-WireOhms Measurements by Scanning Example: Making 4-WireOhms Measurements by Scanning Downloading a Scan List Scanning a Switchbox without a Downloaded Scan List Scanning a Switchbox with a Downloaded Scan List Scanning Voltmeter Configuration with HP E1326B Measuring Temperature Using Thermocouples (HP E1353A Module only) Comments Understanding the HP E1351A/53A FET Multiplexer Modules Commands for Scanning Switchbox Channels Using Scanning Trigger Sources Page Page Example: Scanning with External Instruments Using "Trig Out" and "Event In" Ports Using Stand-Alone Multimeter and Digital Bus Triggering Using Scanning Voltmeter Configuration and Digital Bus Triggering Using the Scan Complete Bit HP E1351A/53A 16-ChannelFET Multiplexer Command Reference Command Types Common Command Format SCPI Command Format Command Separator Abbreviated Commands Implied Commands Note SCPI Command Reference ABORt ARM DISPlay :MONitor:CARD :MONitor[:STATe] Monitoring Switchbox Channels: Selecting the Module to be Monitored: Monitor Mode on an HP 1301 Mainframe Display: Example Enabling the Monitor Mode INITiate Example Enabling Continuous Scans :CONTinuous Example Query Continuous Scanning State Starting the Scanning Cycle: ∙Stopping Scanning Cycles: See the ABORt command OUTPut [ROUTe:] Example Closing Multiplexer Channels CLOSe ∙ Query is Software Readback: The [ROUTe:]CLOSe? command Example Query Multiplexer Channel Closure OPEN Opening Multiplexer Channels OPEN ∙ Query is Software Readback: The [ROUTe:]OPEN? command Query Multiplexer Channel Open State SCAN ∙Scanning Operation: With a valid channel list Stopping Scan: Example Scanning Using External Instruments SCAN:MODE Order of Command Execution: Mode Description: Selecting the 4-Wire SCAN:MODE Example Query Scan Mode SCAN:PORT port Example Selecting the ABUS Port SCAN:PORT Example Query Scan Port SETTling[:TIME] Digital Bus Handshaking: Example Setting 16 μsec SETTling TIME SETTling[:TIME] Example Set and Query the SETTling TIME STATus :OPERation:ENABle SYSTem :CDEScription :CTYPe :ERRor TRIGger :SOURce ∙ Enabling the Trigger Source: The TRIGger:SOURce command Using the Using Digital Bus Trigger: Using External Trigger Inputs: Example Scanning Using External Triggers Scanning Using Bus Triggers :SOURce Example Query Trigger Source IEEE 488.2 Common Commands Command Quick Reference Page HP E1351A/53A FET Multiplexer Specifications Page HP E1351A/53A Register-Based Programming About This Appendix Register Addressing Page The Base Address A16 Address Space Outside the Command Module or Mainframe Register Descriptions Page Register Bit Descriptions Manufacturer ID Register Status/Control Register Scan Control Register Scan Channel Delay Register Scan Channel Configuration Register Configuration Bit (C1 - C0) Executing Commands OUTPut [ROUTe:] SYSTem TRIGger Register-BasedProgramming for Maximum Speed VLD A_D B_D decimal code: Page Multimeter Command and Parameter Opcodes Page Register-Based Programming Error Codes HP E1351A/53A FET Multiplexer Error Messages Page Index