HP E4402B, E4403B, E4404B, E4405B, E4407B, E4408B, E4411B Power Requirements

Installation and Setup

Power Requirements

Power Requirements

The only physical installation of your Agilent spectrum analyzer is a connection to a power source.

Line voltage does not need to be selected.

WARNING Failure to ground the analyzer properly can result in personal injury. Before turning on the analyzer, you must connect its protective earth terminals to the protective conductor of the main power cable. Insert the main power cable plug into a socket outlet that has a protective earth contact only. DO NOT defeat the earth-grounding protection by using an extension cable, power cable, or autotransformer without a protective ground conductor.

If you are using an autotransformer, make sure its common terminal is connected to the protective earth contact of the power source outlet socket.

This is a Safety Class 1 Product (provided with a protective earthing ground incorporated in the power cord). The mains plug shall only be inserted in a socket outlet provided with a protective earth contact. Any interruption of the protective conductor inside or outside of the product is likely to make the product dangerous. Intentional interruption is prohibited.

CAUTION VENTILATION REQUIREMENTS: When installing the product in a cabinet, the convection into and out of the product must not be restricted. The ambient temperature (outside the cabinet) must be less than the maximum operating temperature of the product by 4° C for every 100 watts dissipated in the cabinet. If the total power dissipated in the cabinet is greater than 800 watts, then forced convection must be used.

This analyzer has autoranging line voltage input. Be sure the supply voltage is within the specified range.

NOTE	For more information regarding analyzer specifications, see the Specifications
	guide.

10

Chapter 1

Contents

Getting Started Guide Notice Additional Information 1. Installation and Setup 2. Front and Rear Panel Features 3. Making a Basic Measurement 4. Viewing Catalogs and Saving Files 5. Options and Accessories 6. In Case of Difficulty 1Installation and Setup Page Initial Inspection Page If There Is a Problem Power Requirements Checking the Fuse AC Power Cord Page Table 1-3.AC Power Cords Page Turning on the Analyzer for the First Time Why Aren’t All the Personality Options Loaded in Memory Using an External Reference Firmware Revision TIP Running Internal Alignments Printer Setup and Operation Interconnection and Setup Testing Printer Operation Protecting Against Electrostatic Discharge Legal Information Page 2Front and Rear Panel Features 2.1.1 Front-PanelConnectors and Keys Media Door Earphone Data Control Keys Knob Numeric Keypad Step Keys Option 1DP for Option 1DQ 2.1.2 Display Annotations Screen Annotation (Continued) Page Rear-PanelFeatures 2.2 Rear-PanelFeatures Service Connector Inputs/Outputs Agilent ESA-LSeries (E4403B, E4408B, E4411B) Slot # Agilent ESA-ESeries (E4401B, E4402B, E4404B, E4405B E4407B) IF, Video, and Sweep Ports FM Demod Frequency Extension Assembly Card Slot Identification Numbers Power On Selection Power Always On Power Norm Page Key Overview 2.3 Key Overview Page Front and Rear Panel Symbols 2.4 Front and Rear Panel Symbols 3Making a Basic Measurement Basic Assumption Using the Front Panel Entering Data Using Menu Keys Presetting the Spectrum Analyzer Creating a User Preset Viewing a Signal Figure 3-110 MHz Internal Reference Signal and Associated Spectrum Setting Frequency Span Figure 3-2Span Changed to 50 MHz Reading Frequency & Amplitude Esc Changing Reference Level Page Improving Frequency Accuracy Valid Marker Count Range Figure Increasing Marker Frequency Accuracy Figure 3-6Using Marker Counter 4Viewing Catalogs and Saving Files Page File Menu Functions Locating and viewing files in the catalog Figure 4-1.Catalog Menu Creating a directory Formatting a Floppy Disk Saving a File Step 1. Set up the analyzer trace Figure 4-3.Viewing Trace Figure 4-4.Viewing Traces 1 and Step 2. Save the file Saving Now Loading a file Figure 4-7.Verifying Trace Renaming a File Copying a File Deleting a File Using the Alpha Editor 5Options and Accessories Ordering Options and Accessories Options Page Option Descriptions Page Page Page Page Page Page Page Page Page Page Page Accessories 50 Ohm/75 Ohm Minimum Loss Pad 75 Ohm Matching Transformer AC Probe AC Probe (Low Frequency) Carrying Strap (Part Number E4401-60028) External Keyboard GPIB Cable HP/Agilent 11970 Series Harmonic Mixers HP/Agilent 11974 Series Preselected Millimeter Mixers Agilent E1779A Battery Pack Parallel Interface Cable Printer RF and Transient Limiters RF Bridges RS-232Cable Static Safe Accessories 6In Case of Difficulty No operator serviceable parts inside. Refer servicing to qualified personnel. To prevent electrical shock, do not remove covers Types of Spectrum Analyzer Messages Before Calling Agilent Technologies Check the Basics Page Read the Warranty Service Options Calling Agilent Technologies Table 6-2.Contacting Agilent Technologies Returning an Analyzer for Service FRAGILE, HANDLE WITH CARE Page Index Index-97 Index-98 Index-99