HN System
1037312-0001Revision A March
Copyright 2007 Hughes Network Systems, LLC
Trademarks
Types of warnings used in this manual
Important safety information
DANGER
Safety alert labels on the antenna assembly
Feed support tube Transmitter Reflector back side
Antenna installation safety
procedures
DANGER
DANGER
Do not work in high wind or rain or if a storm, lightning, or other adverse weather conditions are present or approaching
Observe these precautions to avoid exposure to RF radiation, a potential safety hazard
viii
Contents
Chapter
Chapter
Contents 1037312-0001Revision A
Figures
xiii
Chapter
Chapter
Chapter
Chapter
Chapter
31. Securing the feed horn clamp
Tables
Chapter
Chapter
Tables 1037312-0001Revision A
Tables 1037312-0001Revision A
Scope and audience Organization
About this document
xvii
Related publications Revision record
xviii
Chapter
Overview
Chapter 1 Overview 1037312-0001Revision A
The model AN6-098Pantenna
Antenna installation summary
7.Install the antenna reflector - Chapter
9.Install the radio assembly
12.Connect cables to the ODU - Chapter
Tasks related to antenna installation
Selecting the installation site
Installing the antenna mount
Installation Guide
DW60xx, and DW40xx Domestic Installations
Chapter 1 Overview 1037312-0001Revision A
Chapter
Antenna parts and required tools
Tools on page
Related components
Antenna kit components
Two antenna kits for two radio types
Antenna kit
Inspecting the antenna parts
2 boxes
Description of main components
Az/El and reflector bracket assembly
Figure 4 Antenna reflector
feed support tube
Feed horn with protective packing material
Figure 7 Feed horn and waveguide transition
Waveguide transition
Figure 8 Radio assembly mounting adapter
Upper bracket Lower bracket
J-typeradio assembly
Radio assembly types
Vertical shim kit if required
Cradle-typeradio assembly Figure 12 illustrates the cradle-type radio assembly. The main parts of the radio assembly are mounted on two circular brackets so they can be rotated, similar to the movement of a cradle, to set the polarization of the feed horn. The arrows in Figure 13 indicate how the radio assembly can be rotated
Page
Small hardware parts lists
Part
Quantity
Comments
1-inchinside diameter O-ring
Tools
Tool
Details
Hardware size
Determining the pointing values
Assembling the antenna
Chapter
General instructions for assembling the antenna
Fastener
Maximum
torque
Side view
Figure 14 Making sure the mast is plumb
Top view
Reflector bracket Az/El mount assembly
Top canister nut 1 of
Attaching the reflector
4.Partially tighten the screws
Installing the feed support tube
Figure 18 Attaching feed rods to the reflector
Securing the feed support tube
Tightening the hardware Tighten the hardware as follows
Page
Chapter
Installing a J-typeradio assembly
This chapter includes
3.Separate the end of the waveguide from the shim
4. Remove the horizontal shim and O-ring
TRIA
Horizontal shim in place
Vertical shim in place
5.Install the vertical shim and O-ringin the same location. Because of its shape and alignment pins on the transmit/receive isolation assembly TRIA, the vertical shim can only be installed in the position shown in Figure 24 upper right photo. Note the position of the alignment pins. Likewise, the horizontal shim can only be installed in one position
8.Insert and tighten the four Allen screws
Installing the radio assembly
Attaching the upper mounting bracket
Waveguide transition O-ringgroove
O-ring
Make sure the O-ringremains in the O-ringgroove
Radio assembly TRIA
Feed horn
See Figure
4. Tighten the nuts
This completes installation of the radio assembly
5. Tighten the four bolts
1/4-20x 0.75-inch carriage bolts
Upper mounting bracket
Page
Installing a cradle-typeradio assembly
Chapter
Attaching the feed horn
Installing the radio assembly
Screws and washers
Feed horn O-ring
Figure 35 O-ringin groove
This completes installation of the radio assembly
4. Tighten the bolts securely
5/16-18× 2.5-inch
Mounting adapter Feed support tube
Setting polarization for the cradle-typeradio
Calculating the radio polarization setting
Setting the radio polarization
Cabling and connections
Previous cabling work
Cable Connectors, Ground Blocks and Ground Block
Chapter
Transmit cable marked with BLUE tape
Routing the cables at the ODU
Transmitter
Ground connection
Connecting the transmit and receive cables
Transmit cable
Figure 42 Transmit connector - cradle-typeradio
Figure 41 Transmit connector - J-typeradio
4. If necessary, secure the cable with cable ties
4.If necessary, secure the cable with cable ties
Pointing the antenna
Adjusting the antenna on page
Setting coarse elevation on page
Fine elevation adjustment on page
Peaking the signal description
Using the installation software
Antenna pointing overview
Prerequisites for antenna pointing
Outdoor pointing interface
Figure 46 OPI
Adjusting the antenna
½-inchwrench
Fine elevation adjustment nuts
Figure 49 Setting coarse elevation
Elevation scale
Fine elevation adjustment Receive pointing
Figure 50 Fine elevation adjustment
given by the installation software
2.Prepare to make azimuth adjustments as follows
If no signal is present
Peaking the signal procedure
Isolating the transmit signal
Manual ACP test
1.Initiate a manual ACP test
Check for safety labels and signs
Final steps
Page
Acronyms and abbreviations
Page
Index
Page
Page
Index 1037312-0001Revision A
