Manuals / Hunter Fan / Lawn and Garden / Outdoor Ceiling Fan

Hunter Fan 41462-01 Contents, ImportantInformation, Getting Ready, Assembling The Fan

Models: 41462-01

1 26

Page 4

ImportantInformation	5
Step 1 - Getting Ready	6
Step 2 - Installing The Ceiling Plate	8
Step 3 - Assembling The Fan	10
Step 4 - Hanging The Fan	11
Step 5 - Wiring The Fan	12
Step 6 - Attaching The Canopy	14
Step 7 - Assembling Fan Blades	15
Step 8 - Attaching The Switch Housing	16
Step 9 - Remote Control	18
Operating Your Hunter Fan	22
CleaningAndMaintenance	23
Troubleshooting	24

41462-01 10/14/2005

Page 4

Image 4

Contents

Installationand Operation Manual For Hunter Ceiling Fans 41462-01 10/14/200541462-01 10/14/2005 CONGRATULATIONS Model Name Catalog No Serial No Date Purchased Where PurchasedAttach Your Receipt or a Copy of Your Receipt Here CONTENTS Step 5 - Wiring The FanStep 8 - Attaching The Switch Housing Step 9 - Remote ControlTo install a ceiling fan, be sure you can do the following Drill holes for and install wood screwsIdentify and connect electrical wires Lift 40 pounds IMPORTANT INFORMATIONYou will need the following tools for installing the fan STEP 1 - GETTING READYGATHERING THE TOOLS Electric drill with 9/64 bit Standard screwdriverAngle Mounting Figure 1b hangs from a vaulted or angled ceil- ing 29 Max1512.65 PitchSTEP 2 - INSTALLING THE CEILING PLATE Isolators Ceiling Plate Figure 2a - Adding Isolators to Ceiling PlateFigure 2b - Correct Position of Ceiling Plate for Angle Mounting STEP 3 - ASSEMBLING THE FAN Pipe Hanger Bracket Canopy Allen Head Pipe Set ScrewSTEP 4 - HANGING THE FAN STEP 5 - WIRING THE FAN CONNECTING FAN TO ELECTRI- CAL SOURCEPower Black Wires In White Ceiling Bare or Green 2 x 4 Brace Green Approved ConnectorsOutlet Box Ceiling Plate White2. Install and tighten the three canopy screws STEP 6 - ATTACHING THE CANOPYRefer to Figure 41462-01 10/14/2005STEP 7 - ASSEMBLING FAN BLADES Blade Bracket Cover Plate Blade Bracket Assembly ScrewsFigure 7c - Attaching Blade Iron Assembly to Motor Decorative Screw Blade Iron Barrel NutSTEP 8 - ATTACHING THE SWITCH HOUSING ATTACHING THE UPPER SWITCH HOUSINGATTACHING THE LOWER SWITCH HOUSING INSTALLING ACCESSORY LIGHT KITSSTEP 9 - REMOTE CONTROL REMOTE CRADLE INSTALLATION STANDARD LIGHT SWITCHROCKER LIGHT SWITCH WALL INSTALLATIONBATTERY INSTALLATION DIP SWITCH SETTING4. Replace the battery and cover Figure 9dPOWER FAILURE If the fan is not functioning af- ter installationFAN CONTROL Refer to Figure 9f for identification of controlbuttons To turn off the fan. Press the FAN OFF buttonAUTO RESUME LIGHT CONTROLFCC INFORMATION 1. Turn on electrical power to the fan 2. Refer to the STEP 9 - REMOTE CONTROL, for operationcausing a draft OPERATING YOUR HUNTER FANCLEANING AND MAINTENANCE MANUFACTURERS PHONE NUMBERTROUBLESHOOTING PROBLEM1. Power turned off, fuse blown, or circuit breaker tripped 2. Loose wire connections or wrong connectionsSOLUTION 5. Optional Light Kit is not properly installed6. Switch housing is loose Noisy operationRemote battery life seems short Not using alkaline batteriesReplace with alkaline battery Battery too weak