Manuals / Hunter Fan / Lawn and Garden / Outdoor Ceiling Fan

Hunter Fan 41462-01 operation manual Assembling Fan Blades, Decorative Screw Blade Iron Barrel Nut

Models: 41462-01

1 26

Page 15

STEP 7 - ASSEMBLING FAN BLADES

1.Attach each blade to the blade iron using three barrel nuts and three decorative screws as shown in Figure 7a, 7b and 7c.

Decorative

Screw

Blade

Iron

Barrel Nut

Figure 7a - Attaching Blades to Blade Iron

Blade Decorative

Screw

Barrel Nut Blade Iron

Figure 7b

2.Remove the blade mounting screws and rubber shipping bumpers from the motor.

3.Align the holes in the blade bracket and the cover plate with the five holes in the bottom of the motor and partially install the five 1/4"-20 Screws. Refer to Figure 7c.

4.Once all five screws are partially installed, tighten them securely.

WARNING

Failure to securely tighten the 1/4"-20 Screws into the Motor could cause the Blade Assem- bly to fall.

Blade

Bracket

Cover

Plate

Blade

Bracket

Assembly

Screws

Figure 7c - Attaching Blade Iron

Assembly to Motor

41462-01 10/14/2005

Page 15

Image 15

Hunter Fan 41462-01 Assembling Fan Blades, Decorative Screw Blade Iron Barrel Nut, a - Attaching Blades to Blade Iron

Contents

41462-01 10/14/2005 Installationand Operation Manual For Hunter Ceiling Fans41462-01 10/14/2005 Model Name Catalog No Serial No Date Purchased Where Purchased CONGRATULATIONSAttach Your Receipt or a Copy of Your Receipt Here Step 9 - Remote Control CONTENTSStep 5 - Wiring The Fan Step 8 - Attaching The Switch HousingIMPORTANT INFORMATION To install a ceiling fan, be sure you can do the followingDrill holes for and install wood screws Identify and connect electrical wires Lift 40 poundsElectric drill with 9/64 bit Standard screwdriver You will need the following tools for installing the fanSTEP 1 - GETTING READY GATHERING THE TOOLSPitch Angle Mounting Figure 1b hangs from a vaulted or angled ceil- ing29 Max 1512.65Isolators Ceiling Plate Figure 2a - Adding Isolators to Ceiling Plate STEP 2 - INSTALLING THE CEILING PLATEFigure 2b - Correct Position of Ceiling Plate for Angle Mounting Pipe Hanger Bracket Canopy Allen Head Pipe Set Screw STEP 3 - ASSEMBLING THE FANSTEP 4 - HANGING THE FAN CONNECTING FAN TO ELECTRI- CAL SOURCE STEP 5 - WIRING THE FANWhite Power Black Wires In White Ceiling Bare or Green 2 x 4 Brace GreenApproved Connectors Outlet Box Ceiling Plate41462-01 10/14/2005 2. Install and tighten the three canopy screwsSTEP 6 - ATTACHING THE CANOPY Refer to FigureDecorative Screw Blade Iron Barrel Nut STEP 7 - ASSEMBLING FAN BLADESBlade Bracket Cover Plate Blade Bracket Assembly Screws Figure 7c - Attaching Blade Iron Assembly to MotorATTACHING THE UPPER SWITCH HOUSING STEP 8 - ATTACHING THE SWITCH HOUSINGINSTALLING ACCESSORY LIGHT KITS ATTACHING THE LOWER SWITCH HOUSINGWALL INSTALLATION STEP 9 - REMOTE CONTROLREMOTE CRADLE INSTALLATION STANDARD LIGHT SWITCH ROCKER LIGHT SWITCHFigure 9d BATTERY INSTALLATIONDIP SWITCH SETTING 4. Replace the battery and coverTo turn off the fan. Press the FAN OFF button POWER FAILUREIf the fan is not functioning af- ter installation FAN CONTROL Refer to Figure 9f for identification of controlbuttonsLIGHT CONTROL AUTO RESUMEFCC INFORMATION OPERATING YOUR HUNTER FAN 1. Turn on electrical power to the fan2. Refer to the STEP 9 - REMOTE CONTROL, for operation causing a draftMANUFACTURERS PHONE NUMBER CLEANING AND MAINTENANCE2. Loose wire connections or wrong connections TROUBLESHOOTINGPROBLEM 1. Power turned off, fuse blown, or circuit breaker trippedNoisy operation SOLUTION5. Optional Light Kit is not properly installed 6. Switch housing is looseBattery too weak Remote battery life seems shortNot using alkaline batteries Replace with alkaline battery