Manuals / Intel / Computer Equipment / Network Router

Intel 21555 manual Introduction, DIP Switch Operation, Stake-Pin Jumper a

Models: 21555

1 26

Download 26 pages 60.05 Kb

Page 9

Introduction

Table 1. DIP Switch Operation

	Switch	Switch	The Switch Controls	Reference Information
	Pack	Switch	The Switch Controls	Reference Information
	Pack

		SW1, 2, 3	PICMG configurations. (See Chapter 3).	Table 10 on page 21
	J9
	J9			21555 Non Transparent
				21555 Non Transparent
		SW4	PR_AD1 strapping option.	PCI-to-PCI Bridge User’s
				Manual

		SW5	PR_CS to either Flash or optional ROM socket.	Table 8 on page 19

	J20	SW1	PR_AD2 for SROM operation.	Table 7 on page 18

		SW2	PR-AD3 for lockout bit control.
		SW2	PR-AD3 for lockout bit control.

		SW3	PR_AD4 for synchronous or asynchronous clocking.	Table 14 on page 22

		SW4	PR_AD5 for S_CLKO operation.
		SW4	PR_AD5 for S_CLKO operation.

		SW5	PR_AD6 for Central function selection.	Table 12 on page 22

	J21	SW#	The REQ/GNT lines for Arbiter control.	Table 12 on page 22
	J21	(1,2,3,4,5)	The REQ/GNT lines for Arbiter control.	Table 13 on page 22
		(1,2,3,4,5)		Table 13 on page 22

1.5Stake-Pin Jumper

Table 2 shows the configuration and the function of the single stake-pin jumper. J8 enables the DE1B55503 hot-swap functionality, controls operation of LED L1, and connects the l_stat signal to a pullup resistor.

Table 2. Stake-Pin Jumper a

Jumper	Function

	•	When removed, the hot-swap functionality is enabled, and L1 will light.
J8	•	When installed, hot-swap functionality is disabled and the L1 LED is
		extinguished.

a.No jumper is installed by the Factory default.

21555 PCI-to-PCI Bridge Evaluation Board User’s Guide

9

Image 9

Intel 21555 manual Introduction, DIP Switch Operation, Stake-Pin Jumper a

Contents

User’s Guide 21555 PCI-to-PCI Bridge Evaluation BoardNovember 21555 PCI-to-PCI Bridge Evaluation Board User’s Guide Figures ContentsTables J21 Switch Operations for Central Function and Arbiter ControlSwitch Operations for Synchronous or Asynchronous Clock Control 1.2 Features Introduction1.1 Overview 1.3.1 Connectors 1.3 Major ComponentsIntroduction 1.3.2 Switches and Jumper 1.3.3 DevicesIntroduction 1.4 Switch Settings Figure 2. SwitchesIntroduction Table 1. DIP Switch Operation 1.5 Stake-Pin JumperIntroduction Table 2. Stake-Pin Jumper a21555 1.6 Resistor JumpersIntroduction Figure 3. Jumper Resistors1.6.2 Clamping Voltage 1.6.1 Clock ConfigurationTable 3. Clock Configuration Jumpers IntroductionIntroduction 1.7 Secondary Slot Numbering and IDSEL MappingFigure 4. Local PCI Slot Numbering Table 5. Slot and IDSEL Mapping1.8 Interrupt Routing IntroductionTable 6. Interrupt ORing Introduction 1.9 Typical Configurations21555 PCI-to-PCI Bridge Evaluation Board User’s Guide 21555Figure 6 shows the DE1B55503 with two local bus option cards IntroductionFigure 6. DE1B55503 with Two Local Bus Option Cards 21555 PCI-to-PCI Bridge Evaluation Board User’s GuidePage 2.2 Hardware Requirements Operations and Installation2.3 Software Requirements 2.1 SpecificationsOperations and Installation 2.3.1 Programming the SROM2.3.2 Programming the Flash ROM 2.3.2.1 Board Setup 2.4 Installation ProcedureOperations and Installation 2.3.2.2 Running DbFlash.exe2.5 Interrupt Routing Operations and InstallationTable 9. Interrupt ORing Optional Configurations 3.1 PICMG Configuration3.2 Central Function and Arbiter Control 3.3 Asynchronous Clocking Optional ConfigurationsSignal and Default Information A.1 J2 J4, J5, and J6 Connector Pinouts21555 PCI-to-PCI Bridge Evaluation Board User’s Guide Signal and Default Information Table A-2. J4 Pin AssignmentsTable A-3. J5 CBE, REQ, and GNT Signal and Default Information 21555 PCI-to-PCI Bridge Evaluation Board User’s GuideLSTAT A.3 Factory Default Switch and Jumper Configuration A.2 JATAG Connector PinoutSignal and Default Information Table A-5. J1 JATAG Connector