Manuals / Intel / Computer Equipment / Server

Intel S875WP1-E manual AGP Connector, ATA Rage XL Video Controller, Video Modes

Models: S875WP1-E

1 112

Download 112 pages 32.08 Kb

Page 16

AGP Connector

AGP is a high-performance interface for graphics-intensive applications. AGP is independent of the PCI bus and is intended for exclusive use with graphical display devices. The AGP bus follows the AGP 3.0 specification.

The AGP connector on the server board S875WP1-E supports the following:

•2X, 4X, or 8X AGP protocol

•1.5 V add-in cards only

•Maximum bus bandwidth of 2.13 GB/sec

✏NOTE

The AGP connector is keyed for 1.5 V AGP cards only. Do not attempt to install a legacy 3.3 V AGP card. The AGP connector is not mechanically compatible with legacy 3.3 V AGP cards.

ATA Rage XL Video Controller

The S875WP1-E server board provides an ATI Rage XL PCI graphics accelerator, along with

8 MB of video SDRAM and support circuitry for an embedded SVGA video subsystem. The ATI Rage XL chip contains a SVGA video controller, clock generator, 2D and 3D engine, and RAMDAC in a 272-pin PBGA. One 2Mx32 SDRAM chip provides 8 MB of video memory.

The SVGA subsystem supports a variety of modes, up to 1600 x 1200 resolution in 8/16/24/32 bpp modes under 2D, and up to 1024 x 768 resolution in 8/16/24/32 bpp modes under 3D. It also supports both CRT and LCD monitors up to 100 Hz vertical refresh rate.

The server board S875WP1-E provides a standard 15-pin VGA connector and supports disabling of the on-board video through the BIOS Setup menu or when a plug-in video card is installed in the AGP slot or any of the PCI slots.

Video Modes

The Rage XL chip supports all standard IBM* VGA modes. The following table shows the 2D/3D modes supported for both CRT and LCD. The table specifies the minimum memory requirement for various display resolution, refresh rates, and color depths.

Table 3.	Video Modes
2D Mode		Refresh Rate (Hz)	S875WP1-E 2D Video Mode Support
2D Mode		Refresh Rate (Hz)	8 bpp	16 bpp	24 bpp	32 bpp
640x480		60, 72, 75, 90, 100	Supported	Supported	Supported	Supported

800x600		60, 70, 75, 90, 100	Supported	Supported	Supported	Supported

1024x768		60, 72, 75, 90, 100	Supported	Supported	Supported	Supported

1280x1024		43, 60	Supported	Supported	Supported	Supported

1280x1024		70, 72	Supported	–	Supported	Supported

continued

16	Intel Server Board S875WP1-E Product Guide

Image 16

Intel S875WP1-E manual AGP Connector, ATA Rage XL Video Controller, Video Modes

Contents

A Guide for Technically Qualified Assemblers of Intel Identified Intel Server Board S875WP1-E Product GuideSubassemblies/Products Important Safety Instructions DisclaimerContents 1 Server Board Features2 Server Board Installation and Upgrades 3 Configuration Software and Utilities Solving BIOS ProblemsGetting Help Technical Reference7 Regulatory and Integration Information Figures TablesFan Control Configuration Submenu Remote Access Configuration SubmenuHard Disk Drives Submenu Removable Devices Submenu1 Server Board Features Server Board Features continued Server Board Connector and Component Locations Figure 1. Server Board ComponentsBack Panel Connectors Front Panel ConnectorsFigure 2. Back Panel Connectors Figure 3. Front Panel ConnectorsProcessor MemoryIntel 82875P Memory Controller Hub MCH Intel 875P Chipsethttp//support.intel.com/support/motherboards/server/S875WP1-E Intel 82801EB I/O Controller Hub ICH5-R VideoIntel 82802AC Firmware Hub FWH ATA Rage XL Video Controller AGP ConnectorVideo Modes Super I/O Video Memory InterfaceKeyboard and Mouse Connectors Serial PortParallel Port Floppy Drive ControllerHigh-Speed USB 2.0 Support Legacy USB SupportPCI I/O Subsystem 32-bit, 33-MHz PCI SubsystemSerial ATA SATA Data StorageDevice IDs IDSEL SCSI Hard Drive Activity LED Connector IDE InterfacesNIC Connector and Status LEDs Network Interface Controller NICPower Management Software Support through ACPIACPI features include LAN Wake Wake-up Devices and EventsPCI via PME# Wake-up Support Hardware Support Resume on RingWake from USB Wake from PS/2 DevicesPower Connector Fan ConnectorsInstantly Available PC Technology Figure 4. Location of the Standby Power Indicator LED CR7J1Hardware Management and Monitoring Chassis Intrusion and DetectionPassword Security Real-Time Clock, CMOS SRAM, and Battery Recovering the CMOSPCI Auto Configuration BIOSIDE Auto Configuration BIOS Updates Language SupportRecovering BIOS Data Boot OptionsCD-ROM and Network Boot Custom Splash ScreenBooting Without Attached Devices Fast Booting Systems with Intel Rapid BIOS BootIntel Rapid BIOS Boot System Management BIOS SMBIOS Page 2 Server Board Installation and Upgrades Tools and Supplies NeededBefore You Begin Warnings and CautionsCAUTIONS Installing the I/O Shield Figure 6. Installing the I/O ShieldInstalling Chassis Standoffs Intel Server Chassis SC5200Intel Server Chassis SC5250-E Figure 8. Installing Chassis Standoffs in the SC5250-E ChassisK L M TP00188Placing the Server Board into the Chassis Installing the Server BoardAttaching the Server Board Installing the Processor 6. Place the fan heat sink on top of the processor Figure 13. Attaching the Fan Heat Sink Clips to the Processor Socket Figure 14. Attaching the Fan Heat Sink Clips to the Processor SocketRemoving the Processor TP00201DIMM Installation Guidelines Installing and Removing Memoryhttp//support.intel.com/support/motherboards/server/S875WP1-E Installing DIMMs Figure 16. DIMM Socket LocationsInstalling and Removing an AGP Card Removing DIMMsRemoving the AGP Card Installing an AGP CardFigure 17. Installing the AGP Card Connecting the IDE Cable Connecting the Serial ATA Cable Optional Figure 19. Connecting the SATA CableConnecting Internal Headers Connecting the Front Panel HeaderTable 12. Front Panel Header J7J1 continued Connecting the USB 2.0 HeaderTable 13. USB 2.0 Header J7E1 Connecting Hardware Control and Power Cables Figure 21. Location of the Fan Headers and Power ConnectorsSetting the BIOS Configuration Jumper Connecting FansConnecting Power Cables Chassis IntrusionClearing Passwords Table 14. Jumper Settings for the BIOS Setup Program Modes J8J2Replacing the Battery PRECAUTIONFORHOLDSREGEL VIKTIGTVARO VORSICHTAVVERTIMENTO PRECAUCIÓNFigure 23. Removing the Battery TP001973 Configuration Software and Utilities Updating the BIOS with the Intel Flash Memory Update UtilityObtaining the BIOS Update File http//support.intel.com/support/motherboards/serverRecording the Current BIOS Settings Creating Bootable MediaCreating a Bootable CD Creating a Bootable DisketteCreating a BIOS Update Media http//support.intel.com/support/motherboards/serverUpdating the BIOS Recovering the BIOS Using the Setup Program BIOS Setup Program ModesMaintenance Menu Table 16. BIOS Setup Program Function KeysMaintenance Table 17. Maintenance MenuMain Menu Table 18. Main MenuAdvanced Menu Table 19. Advanced MenuPCI Configuration Submenu Table 20. PCI Configuration SubmenuBoot Configuration Submenu Table 21. Boot Configuration SubmenuPeripheral Configuration Submenu Table 22. Peripheral Configuration SubmenuTable 22. Peripheral Configuration Submenu continued Drive Configuration Submenu The menu represented in Table 23 is used to configure drive optionsDrive Configuration Table 23. Drive Configuration SubmenuTable 23. Drive Configuration Submenu continued Primary/Secondary/SATA-0/SATA-1 Master/Slave Submenus Table 24. Primary/Secondary/SATA-0/SATA-1 Master/Slave SubmenusFloppy Configuration Submenu Table 25. Floppy Configuration SubmenuEvent Log Configuration Submenu Table 26. Event Log Configuration SubmenuVideo Configuration Submenu Table 27. Video Configuration SubmenuUSB Configuration Submenu Table 28. USB Configuration SubmenuChipset Configuration Submenu Table 29. Chipset Configuration SubmenuTable 29. Chipset Configuration Submenu continued Fan Control Configuration Submenu Table 30. Fan Control Configuration SubmenuHardware Monitoring Submenu Table 31. Hardware Monitoring SubmenuRemote Access Configuration Submenu Table 32. Remote Access Configuration SubmenuSecurity Menu Table 33. Security MenuPower Menu ACPI SubmenuPower Table 34. Power MenuBoot Menu Table 36. Boot MenuBoot Device Priority Submenu Hard Disk Drives SubmenuTable 37. Boot Device Priority Submenu Table 38. Hard Disk Drives SubmenuRemovable Devices Submenu ATAPI CDROM Drives SubmenuTable 39. Removable Devices Submenu Table 40. ATAPI CDROM Drives SubmenuExit Menu Table 41. Exit MenuPage 4 Solving BIOS Problems BIOS Beep CodesBIOS Error Messages Table 43. BIOS Error MessagesError Message Table 43. BIOS Error Messages continuedExplanation Page 5 Getting Help World Wide WebTelephone http//support.intel.com/support/motherboards/server/S875WP1-EPage Server Board Connectors 6 Technical ReferencePower, Fan, Chassis Intrusion Connectors Baseboard ConnectorsFigure 24. Power, Fan, and Chassis Intrusion Connectors Figure 25 shows the add-in board and peripheral interface connectors Add-In Board and Peripheral Interface ConnectorsFigure 25. Add-in Board and Peripheral Interface Connectors Server Board Resources Memory MapDMA Channels Table 44. System Memory MapI/O Map Table 46. I/O MapInterrupts Table 47. InterruptsProduct Safety Compliance 7 Regulatory and Integration InformationProduct Regulatory Compliance Product EMC ComplianceTable 48. Product Certification Markings Product Regulatory Compliance MarkingsIntel Server Board S875WP1-E Product Guide Electromagnetic Compatibility Notices FCC USAIndustry Canada ICES-003 Europe CE Declaration of ConformityTaiwan Declaration of Conformity Korean RRL ComplianceInstallation Requirements Installation PrecautionsPrevent Power Supply Overload Use Only for Intended Applications Place Battery MarkingCAUTIONS