B.Remove the hand brake.

C.Turn the adjustment lever COUNTERCLOCK- WISE.

D.Insert push handles into side frames with the hand grip facing the back of the rollator.

3.Perform one (1) of the following:

INSTALLING BRAKE KIT (BEFORE 3/7/00) - Install NEW hand brake.

A.Position the handbrake assembly under the push handle so the lock button is facing OUT, the tip of the hand brake is towards the end of the hand grip and the brake cable is AWAY from the hand grip.

B.Position the hook portion of the hand brake clamp through the slot in the hand brake assembly.

C.Install the washer, hex bolt and locknut to secure the hand brake assembly to the push handle.

D.Securely tighten the locknut.

INSTALLING BRAKE KIT (AFTER 3/8/00) - Install

NEW hand brake.

A. Push the NEW hand brake onto the push handle.

NOTE:Ifnecessary,twistthehandbrakewhilepushingto installonthepushhandle.

B.AlignthemountingholesoftheNEWhandbrakewith themountingholeinthepushhandle.

C.Installthephillipsscrewthroughbothmountingholes. Securelytighten.

D.Apply a thin coat of hair spray on the inside of the foam grip and on the push handle.

NOTE: This application will make it easier to slide the grip onto the push handle.

E. Slide new grip onto one end of the push handle.

4.Adjust the push handle. Refer to ADJUSTING SPRINT ANDSPARTANPUSHHANDLESinthisinstructionsheet.

5.Adjust the hand brake. Refer to ADJUSTING SPRINT ANDSPARTANHANDBRAKESinthisinstructionsheet.

INSTALLING/REMOVING THE HAND

INSTALLING/REMOVING THE HAND

BRAKE (BEFORE 3/7/00) - STEPS 2 AND 3

BRAKE (AFTER 3/8/00) - STEPS 2 AND 3

Hex Bolt (STEPS

Hand Brake Clamp (STEP 3B)

Hand Brake

Phillips Screw

 

 

 

Hook (STEP 3B)

Adjustment

2A AND 3C)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Nut

Mounting Hole

Washer (STEPS

 

 

 

Slot (STEP 3B)

 

 

 

2A AND 3C)

 

 

 

 

 

 

 

 

 

 

 

 

Locknut (STEPS

 

 

 

 

Lock Button

 

 

Hand Grip

 

 

 

 

 

 

2A AND 3C)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Push Handle

Push Handle

 

 

 

Hand Brake (STEP

Hand Brake Nut

 

 

 

 

2B AND 3A)

Hand Brake

 

 

 

 

 

 

 

 

 

INSTALLING PUSH HANDLE

INSTALLING THE TIRE - STEP 1

 

- STEPS 2 AND 3

 

 

Cap Cover (STEP 3A)

Push Handle

 

 

Hand Grip

 

 

 

 

 

 

 

(STEP 3A)

 

 

(STEPS 2D

 

 

 

Tire (STEP 3C)

 

 

 

 

AND 3A)

 

Textured

Tip of Hand

 

 

 

 

 

 

 

 

Brake

 

 

Brake Cable

 

Tubing

 

Locknut (STEP 3B)

 

(STEP 3A)

 

(STEP 3A)

 

 

Screw

 

 

 

 

 

 

 

Adjustment Lever

(STEP 3B)

Cap Cover

 

 

(STEP 2A)

 

(STEP 3A)

 

 

 

FIGURE 5 - REPLACING SPARTAN CANES AND BRAKES - ASSEMBLING SPARTAN FOR USE

7

Page 7
Image 7
Invacare 65420 Installing Brake KIT After 3/8/00 Install, NEW hand brake Push the NEW hand brake onto the push handle