INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Tape measure

Wrench or pliers

Level

⁵⁄₁₆" nut driver

Phillips screwdriver

¼" nut driver

Flat-blade screwdriver

Drill

Saber or keyhole saw

¹⁄₈" (3.2 mm) drill bit

Marker or pencil

³⁄₁₆" (4.8 mm) carbide-tipped

 

 

 

masonry drill bit (for concrete/

 

 

 

ceramic floors)

Parts supplied

Check that all parts are included.

3 - #10-32 hex nuts (attached to terminal block)

3 - Terminal lugs

2 or 3 - Oven racks (depending on your model)

Blower motor

2 - vent clamps

Flexible vent

Flow tester card

Blower location template

4 - #8 x ¾" screws (for mounting blower motor bracket)

2 - #12 x 1⁵⁄₈" screws (for mounting anti-tip bracket)

Anti-tip bracket (taped to package containing literature in oven cavity)

Anti-tip bracket must be securely mounted to back wall or floor. Thickness of floor may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

Parts needed

One of the following Jenn-Air wall caps:

Jenn-Air®5" (12.7 cm) Round Surface Wall Cap Damper. Order Part Number A405.

Jenn-Air®6" (15.2 cm) Round Surface Wall Cap Damper. Order Part Number A406.

Jenn-Air®3¼" x 10" (8.3 x 25.4 cm) Surface Wall Cap Damper. Order Part Number A403.

To order, see the “Assistance or Service” section of the Use and Care Guide.

Metal ducting

Vent clamps

Concrete anchors (for concrete floor mounting)

2 - 2" x 4" x 8¾" (5.0 x 10.2 x 22.2 cm) wood spacers (for left or right side venting)

If using a power supply cord:

A UL listed power supply cord kit marked for use with ranges. The cord should be rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends.

A UL listed strain relief.

Check local codes. Check existing electrical supply. See “Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the right-hand side of the oven frame behind the storage drawer panel.

The range should be located for convenient use in the kitchen.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

The floor anti-tip bracket must be installed. To install the anti- tip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

Grounded electrical supply is required. See “Electrical Requirements” section.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

Mobile home installations require:

When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

Four-wire power supply cord or cable must be used in a mobile home installation. The appliance wiring will need to be revised. See “Electrical Connection” section.

3

Page 3
Image 3
Jenn-Air W10253462A installation instructions Installation Requirements, Tools and Parts, Location Requirements

W10253462A specifications

The Jenn-Air W10253462A is a highly regarded appliance in the realm of kitchen innovation. This sophisticated range is known for its blend of style, versatility, and cutting-edge technology, making it an essential addition for both cooking enthusiasts and professional chefs alike.

One of the main features of the W10253462A is its powerful induction cooking capabilities. Induction cooking utilizes electromagnetic energy to heat pots and pans directly, resulting in faster cooking times and improved energy efficiency. This technology not only reduces cooking time but also provides precise temperature control, allowing for a seamless cooking experience. Additionally, the smooth surface of the induction cooktop makes it easy to clean, as spills can be wiped away without difficulty.

Another standout characteristic of the W10253462A is its oven performance. This model typically includes a convection oven which circulates hot air for even cooking results. The convection feature ensures that meals are cooked evenly, reducing the chances of hot spots and undercooked areas. Furthermore, with multiple cooking modes, users can roast, bake, or broil with ease, providing versatility for various recipes.

The appliance often includes advanced safety features as well. For example, the induction cooktop generally comes with automatic shut-off functionality, which turns off the burners if no cookware is detected, ensuring peace of mind when cooking. Additionally, child lock settings are available, making this range a safe option for families.

In terms of aesthetics, the Jenn-Air W10253462A typically boasts a sleek, modern design that complements any kitchen decor. The stainless steel finish not only enhances its visual appeal but also contributes to its durability and resistance to smudges and fingerprints.

Moreover, the appliance often incorporates smart technology, allowing users to control their cooking settings remotely through a smartphone app. This innovation not only increases convenience but also enables users to monitor their dishes' progress from anywhere in the house.

The Jenn-Air W10253462A is truly a blend of sophisticated design and advanced technology, suitable for anyone looking to enhance their cooking experience. With its induction cooking, advanced oven features, safety mechanisms, and smart capabilities, this appliance stands out as a top choice for modern kitchens.