INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■

Tape measure

■

Wrench or pliers

■

Level

■

⁵⁄₁₆" nut driver

■

Phillips screwdriver

■

¼" nut driver

■

Flat-blade screwdriver

■

Drill

■ Saber or keyhole saw

■ ¹⁄₈" (3.2 mm) drill bit

■

Marker or pencil

■

³⁄₁₆" (4.8 mm) carbide-tipped

 

 

 

masonry drill bit (for concrete/

 

 

 

ceramic floors)

Parts supplied

Check that all parts are included.

■3 - #10-32 hex nuts (attached to terminal block)

■3 - Terminal lugs

■2 or 3 - Oven racks (depending on your model)

■Blower motor

■2 - vent clamps

■Flexible vent

■Flow tester card

■Blower location template

■4 - #8 x ¾" screws (for mounting blower motor bracket)

■2 - #12 x 1⁵⁄₈" screws (for mounting anti-tip bracket)

■Anti-tip bracket (taped to package containing literature in oven cavity)

Anti-tip bracket must be securely mounted to back wall or floor. Thickness of floor may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

Parts needed

■One of the following Jenn-Air wall caps:

Jenn-Air®5" (12.7 cm) Round Surface Wall Cap Damper. Order Part Number A405.

Jenn-Air®6" (15.2 cm) Round Surface Wall Cap Damper. Order Part Number A406.

Jenn-Air®3¼" x 10" (8.3 x 25.4 cm) Surface Wall Cap Damper. Order Part Number A403.

To order, see the “Assistance or Service” section of the Use and Care Guide.

■Metal ducting

■Vent clamps

■Concrete anchors (for concrete floor mounting)

■2 - 2" x 4" x 8¾" (5.0 x 10.2 x 22.2 cm) wood spacers (for left or right side venting)

If using a power supply cord:

■A UL listed power supply cord kit marked for use with ranges. The cord should be rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends.

■A UL listed strain relief.

Check local codes. Check existing electrical supply. See “Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the right-hand side of the oven frame behind the storage drawer panel.

■The range should be located for convenient use in the kitchen.

■To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

■The floor anti-tip bracket must be installed. To install the anti- tip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

■Grounded electrical supply is required. See “Electrical Requirements” section.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

Mobile home installations require:

■When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

■Four-wire power supply cord or cable must be used in a mobile home installation. The appliance wiring will need to be revised. See “Electrical Connection” section.

3

Page 2 Page 4
Page 3
Image 3
Jenn-Air W10430955A installation instructions Installation Requirements, Tools and Parts, Location Requirements
Page 2 Page 4

W10430955A specifications

The Jenn-Air W10430955A is a premium kitchen appliance designed to elevate culinary experiences and integrate seamlessly into modern kitchens. As a vital component of Jenn-Air's commitment to innovation and performance, the W10430955A represents a fusion of advanced technology and stylish design.

One of the standout features of the W10430955A is its precision cooking technology. This appliance is engineered to provide consistent, even cooking results, thanks to its advanced temperature management system. This system allows home cooks to achieve professional-grade results, whether they are baking, roasting, or broiling.

Moreover, the W10430955A incorporates a sleek, intuitive control panel that simplifies operation. With its user-friendly interface, cooks can easily select settings, adjust temperatures, and monitor cooking times with precision. The touch-sensitive controls not only enhance functionality but also contribute to the overall aesthetic of the appliance, offering a modern touch to any kitchen decor.

In terms of design, the W10430955A features a contemporary look with high-quality materials, including stainless steel finishes that are both durable and easy to clean. The appliance is also designed for energy efficiency, which not only reduces utility bills but also makes it an environmentally friendly choice for those striving to minimize their carbon footprint.

Another commendable characteristic of the W10430955A is its flexibility in cooking options. It often includes multiple cooking modes that cater to various culinary techniques, providing versatility for a wide range of dishes. Whether preparing a delicate soufflé or a hearty casserole, this appliance stands out for its adaptability.

Furthermore, maintenance is hassle-free with this model. Many components are designed for easy removal and cleaning, ensuring that users can keep their appliance in optimal condition with minimal effort.

Overall, the Jenn-Air W10430955A is an exceptional combination of performance, style, and convenience. Its innovative technologies and user-friendly features make it an ideal choice for both amateur cooks and seasoned chefs looking to enhance their culinary skills in a modern kitchen setting. Investing in this appliance not only elevates cooking experiences but also adds a touch of elegance to any home.
Top Page Image Contents