NetScreen-5200 Power Recommendations | Juniper Networks 5000 SERIES

Chapter 1 Overview

NetScreen-5200 Power Recommendations

Although the NetScreen-5200 can run with one power supply, it is advisable to install both. This practice minimizes the likelihood of system failure due to individual power supply failure.

When either power supply fails, the Alarm LED on the management module glows red. If both are operational, the Alarm LED is off. For more information on power supply LEDs, see Appendix B, Port Descriptions and LED Status.

NetScreen-5400 Power Recommendations

When the NetScreen-5400 contains only two modules, it can operate with one power supply. However, if the system contains three or four modules, the system requires at least two power supplies. In either case, it is advisable to install all three power supplies. This practice minimizes the likelihood of system failure due to individual power supply failure.

When any power supply fails, the Alarm LED on the management module glows red. While all three are operational, the Alarm LED is off. For more information on power supply LEDs, see Appendix B, Port Descriptions and LED Status.

The DC Power Supply

The DC power supply weighs about three pounds. The faceplate contains a power LED, a power switch, a cooling fan vent, and three DC power terminal blocks that connect to power cables.

The figure below shows the NetScreen-5200 DC power supply.

Thumbscrew

Power			DC Power
LED				Terminal
				Blocks
				Blocks
			Grounding
				Screw
				Screw

Power Switch

6	User’s Guide

Image 14

Juniper Networks 5000 SERIES NetScreen-5200 Power Recommendations, NetScreen-5400 Power Recommendations, DC Power Supply

Contents

NETSCREEN-5000 Series Copyright Notice Language Contents Language Contents Table of Contents Servicing the Device Index Table of Contents Viii Preface Guide Organization Juniper Networks Netscreen Publications Command Line Interface CLI ConventionsSet admin user name1 password xyz Overview1 NETSCREEN-5000 Series NetScreen-5200NetScreen-5400 Power Supplies DC Power Supply NetScreen-5200 Power RecommendationsNetScreen-5400 Power Recommendations AC Power Supply FAN Modules 5000-M Management Module Management ModulesNETSCREEN-5000 Modules 5000-M2 Management Module NetScreen-5000 Modules Secure Port Modules 5000-8G SPM 5000-2G24FE SPM Overview User’s Guide Installing the Device General Installation Guidelines Equipment Rack Installation Guidelines NetScreen-5200 Front and Rear Mount Mounting the NETSCREEN-5000 Series NetScreen-5200 Mid-Mount NetScreen-5400 Front Mount Installing and Connecting the AC Power Supply Installing and Wiring a DC Power Supply 48V COMThumbscrew Power Connecting the NETSCREEN-5000 Series to a Router or Switch Establishing AN HA Connection Installing the Device User’s Guide Configuring the Device Operational Modes Transparent ModeRoute Mode NetScreen-5200 Interfaces NETSCREEN-5000 Interfaces Configurable Interfaces NetScreen-5400 Interfaces Performing Initial Connection and Configuration Establishing a Terminal Emulator Connection Upgrading the Firmware During the Boot Process Viewing Current Interface Settings Changing Your Admin Name and PasswordSetting Port and Interface IP Addresses Setting the IP Address of the Management Interface Setting the IP Address for the Trust Zone Interface Setting the IP Address for the Untrust Zone Interface Allowing Outbound Traffic Starting a Console Session Using TelnetConfiguring the Device for Telnet and Webui Sessions Telnet Starting a Console Session Using DialupEstablishing a GUI Management Session Get chassis Configuring the Chassis AlarmHttp//10.100.2.183 Get interface Get interface aggregate1 Configuring Aggregate InterfacesSet interface string zone zonename Using CLI Commands to Reset the Device Following CLI command unset admin device-reset Press the y key Following message appears Servicing the Device Replacing a DC Power Supply Removing and Reseating Modules Replacing AN AC Power Supply Replacing the FAN Tray Connecting and Disconnecting Gigabit Ethernet Cables Removing and Installing a MINI-GBIC Transceiver Servicing the Device User’s Guide Specifications NETSCREEN-5200 Attributes Electrical SpecificationEnvironmental Specification NETSCREEN-5400 Attributes Nebs Certifications Safety CertificationsConnectors EMI Certifications Appendix a Specifications User’s Guide Port Descriptions and LED Status B Module Port Descriptions MGT Status LED States Interpreting Status LEDs for the Management ModulesModule LED Descriptions Interpreting Status LEDs for the Secure Port Module Interpreting Ethernet Port Status LEDs for All Modules Power Supply Leds Interpreting Power Supply LED Status for the NetScreen-5200Interpreting Power Supply LED Status for the NetScreen-5400 Single SPM Installed FAN LED Index User’s Guide Table des matières Chapitre Entretien de l’unité Index 103 Table des matières Xii Manuel de l’utilisateur Préface Organisation DU Manuel Set admin user nom1 password xyz Publications Juniper Networks Netscreen Présentation générale Série DE Produits NETSCREEN-5000 Unité NetScreen-5200Unité NetScreen-5400 Blocs D’ALIMENTATION Bloc d’alimentation CC DEL Bloc d’alimentation CA Modules DE Ventilation Module de gestion 5000-M Modules de gestionModules NETSCREEN-5000 Module de gestion 5000-M2 Modules NetScreen-5000 Modules de ports sécurisés SPM 5000-8G SPM 5000-2G24FE Chapitre 1 Présentation générale Manuel de l’utilisateur Installation de l’unité Instructions D’INSTALLATION Générales Instructions D’INSTALLATION DE LA Baie DE Équipement Montage avant et arrière de l’unité NetScreen-5200 Montage DE L’UNITÉ DE LA Série NETSCREEN-5000 Montage à mi-hauteur de l’unité NetScreen-5200 Montage frontal de l’unité NetScreen-5400 Installation ET Connexion DU Bloc Dalimentation CA Installation ET Raccordement D’UN Bloc ’ALIMENTATION CD COM Établissement D’UNE Connexion HA Chapitre 2 Installation de l’unité Manuel de l’utilisateur Configuration de l’unité Modes DE Fonctionnement Mode TransparentMode Route Interfaces NetScreen-5200 Interfaces NETSCREEN-5000 Interfaces configurables Interfaces NetScreen-5400 Exécution DE LA Connexion ET DE LA Configuration Initiales Établissement d’une connexion d’émulateur de terminal Chapitre 3 Configuration de l’unité Affichage des paramètres d’interface actuels Configuration des adresses IP de port et d’interfaceConfiguration de l’adresse IP de l’interface de gestion Set interface mgt ip adrip/masque Get interface ethernet2/2 Get interface mgtSet interface ethernet2/2 ip adrip/masque Set interface ethernet2/3 ip adrip/masque Démarrage d’une session de console à l’aide de TelnetAutorisation du trafic sortant Telnet Configuration DE L’ALARME DE Châssis Configuration D’INTERFACES Agrégées Set interface chaîne zone nomdelazone Série de produits NetScreen-5000 Appuyez sur la touche y Le message suivant s’affiche Entretien de l’unité Retrait ET Réinstallation DES Modules Remplacement D’UN Bloc D’ALIMENTATION CC Remplacement D’UN Bloc D’ALIMENTATION CA Remplacement DU Bloc DE Ventilation Connexion ET Déconnexion DES Câbles Gigabit Ethernet Retrait ET Installation D’UN Transmetteur MINI-GBIC Chapitre 4 Entretien de l’unité Manuel de l’utilisateur SpécificationsA Spécifications Électriques Attributs DE L’UNITÉ NETSCREEN-5200Attributs DE L’UNITÉ NETSCREEN-5400 Spécifications Environnementales Certifications EMI Certifications NebsCertifications DE Conformité Connecteurs Annexe a Spécifications Manuel de l’utilisateur Série de produits NetScreen-5000 Description DES Ports DES Modules Etats DES DEL D’ÉTAT Interprétation des DEL d’état des modules de gestionDescription DES DEL DES Modules Interprétation des DEL d’état des modules de ports sécurisés Un seul SPM installé DEL DES Blocs D’ALIMENTATION DEL DE Ventilation FAN Nombres 104 Manuel de l’utilisateur