JVC DR-MX1S Manual Timer Programming

6 Press w e to select “START”, then press rt to set the desired start time.

5 Press rt to select the blank number, then press ENTER. The program screen appears.

PROGRAM 4

PR START STOP CH 1 8:00P 10:00 12 2 10:00A 10:45 40 3 11:30P 1:00 125 4 5 6 7 8

(PROGRAM) TO END

VCR PLUS+ PRGM PROGRAM / CONFIRM

R,T THEN (ENTER)

(PROGRAM) TO END

			TIMER RECORDING ON VHS DECK EN 61
Manual Timer Programming			7 Press w e to select “STOP”, then press rt to set the desired
			stop time.
You can program this unit to timer-record as many as 8 programs.			● Each press of rt increases/decreases the stop time in 1-minute
			interval.
If you do not know the PlusCode number for the program you wish			● To increase/decrease the stop time in 30-minutes interval, press and
to record, use the following procedure to set your unit to timer-			hold rt.
record the program.			8 Press w e to select “DATE”, then press rt to set the desired
● Make sure that the unit’s built-in clock is set properly.			date.
			● The current date appears on the TV screen. The date you enter
● Turn on the unit.			appears in its place.
● Turn on the TV and select the video channel (or AV mode).			9 Press w e to select “CH”, then press rt to select the desired
● Slide the TV/CABLE/DBS/DVD switch to DVD.
			channel.
	CABLE/DBS		10 Press REC MODE to select the desired recording mode. Or
			press w e to select “SP/EP”, then press rt to select the desired
	TV	DVD
VHS TIMER			recording mode.
			11 Press ENTER to access the Program Check screen.
VHS
	0-9		12 Press PROGRAM to complete timer programming.
			“PROGRAM COMPLETED” appears on the TV screen for about 5
			seconds, then the normal screen appears. If “PROGRAM NOT
			COMPLETED PROGRAM OVERLAP” appears on the TV screen,
	PROGRAM		see page 62.
			● To program another timer, repeat steps 3 - 12.
	rtwe		13 Press VHS TIMER to engage the unit’s timer mode. The VHS
ENTER			recording lamp lights up on the unit and the HDD or DVD deck is
			automatically selected. When the HDD or DVD deck is in timer
			standby mode, the unit is automatically turned off.
			● To disengage the timer mode, press VHS TIMER again.
			NOTES:
			● To Timer-Record Weekly Or Daily Serials:
REC MODE			— anytime during steps 8 through 10, press number key “9” for
			weekly serials or number key “8” for daily serials (Monday - Friday).
			Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the
			button again makes the corresponding indication disappear.
			● You can program this unit to timer-record as many as 8 programs. If
			you try to program the unit to record a ninth, “PROGRAM FULL”
			appears on the TV screen. To record the extra program, you must
1 Load a cassette with the record safety tab intact.			first cancel any unnecessary programs. ( pg. 62)
			● In case of a power failure after programming, the unit’s memory
2 Press VHS so that the VHS lamp lights up on the unit.			backup keeps your selections for approximately 5 seconds.
3 Press PROGRAM to access the Program screen.			● Programs that start after midnight must have the next day’s date.
			● To record the programs received by cable box or DBS receiver,
4 Press rt to select “PROGRAM/	PROGRAM		record on the HDD or the DVD discs. For details, refer to “Manual
CONFIRM”, then press ENTER			Timer Programming” ( pg. 57).

access the Program Check screen.

●Each press of rt increases/ decreases the start time in 1-minute interval.

●To increase/decrease the start time in 30-minutes interval, press and hold rt.

DATE 12/24 12/25 12/25

START		STOP
– –:– –AM		– –:– –AM
DATE		CH	SP/EP
– –/– –/– –	– – –			SP

PRESS (RTYU, 8=DAILY 9=WEEKLY), THEN (ENTER)

(PROGRAM) TO END