Connecting the Power Cord Supplied, Remove the lens cap | JVC G1000

Connecting to Various Devices (Cont.)

Connecting the Power Cord (Supplied)

After all devices have finished being connected, connect the projector’s power cord. At this time, do not turn on the MAIN POWER switch yet.

1

Power cord (supplied)

2

CAUTION

To prevent fire and electric shock, observe the following:

•When you do not use devices, pull out their power cords from wall outlets.

•Do not connect the devices with power cords other than supplied.

•Do not use voltage other than the power voltage indicated.

•Do not scar, damage, or work on the power cords. Also, do not put a heavy object on, heat or pull the power cords, otherwise they may be damaged.

•Do not insert or pull out the plugs with a wet hand.

-

+

1Insert the supplied power cord

into the power input terminal (AC IN ~) of the projector.

AC IN ~

2Insert the plug of the supplied power cord into a wall outlet.

CAUTION

•Since the power requirement of the projector is high, be sure to insert the power plug directly into a wall outlet.

■To use the projector

•Remove the lens cap.

*The lens cap has a string attached and it is fixed to the projector.

Be sure to fit lens cap when not in use.

Lens cap

24

G1000[D] p.15-25

24

99.2.24, 5:50 PM

Image 24

JVC G1000 manual Connecting the Power Cord Supplied, To use the projector, Remove the lens cap

Contents

G1000 Safety Precautions About burning-in of the D-ILA device Safety Precautions Lighters that present special hazards when over heatedLamp is turned on. Exposure of your eyes to the strong Xenon gas is enclosed with high pressure inside the light Contents Accessories Controls and Features Front Side / Top Surface / Right Side AC in power input terminal Main Power switchConnector panel Adjustable foot for horizontal angle adjustment Refer to Precautions for Installation on Bottom SurfaceAir intake area filter Opening for replacing the light-source lamp Control Panel Setting button When a menu is shownVideo button Computer button Connector Panel C S video input terminal Mini DIN 4 pinRS-232C terminal D-sub 9 pin Computer OUT computer output terminal D-sub 3-row 15 pin Input of external sync signals is automatically detected Audio input terminal stereo mini jackRow 15 pin Audio audio input terminal stereo mini jack Remote Control Unit Installing Batteries Install the batteriesPrecautions for using batteries Open the back cover Installing the Projector Precautions for InstallationDo not install the projector in the following places When installing the projector, observe the followings Projection Distance and Screen Size Projection screen size diagonal lengthCenter line of the lens Projection 55.76 ft 17.0 m 294 Approx cm 443 59.04 ft 18.0 m 311 Approx cm 46962.32 ft 19.0 m 328 Approx cm 495 65.6 ft 20.0 m 345 Approx cm 521 Effective Range and Distance of the Remote Control Unit Effective range and distance of the remote control unitUse the projector with A+B about 10 m 32.8 ft or less Connecting to Various Devices Signals that Can Be Input to the ProjectorVideo signals Computer signals Connecting to Video Devices Connecting to Hi-Vision DevicesVideo devices Hi-Vision devices Connecting to Other Devices Connecting to Devices which Control the ProjectorDesktop type To Audio OUT Connecting to Computer Devices Connection to an IBM PC or IBM-compatible computerRead the manual which comes with each device thoroughly RGB output devices To R To monitor connector Supplied Connection to MacintoshPersonal computer connection cable Connecting the Power Cord Supplied To use the projectorRemove the lens cap To prevent fire and electric shock, observe the following When Turning On the Devices Connected to the Projector Turning on the Power Turn on the Main Power switchBasic Operations Changes to steady on Adjust the screen size When you press VideoWhen you press Computer Follows Adjust focus Adjust sound volumeAdjust focus with the remote control’s Focus + Buttons To turn off video image and audio sound temporarily To use the quick alignment functionProjector’s button Press once Remote control unit To display the Setting menu To use the remote control’s Preset buttonProjector button To display the Main menu Operating the Setting Menu Making Basic SettingsPress the Setting button of the projector Press the Setting button to select the desired item Operating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Changing the Color System Select Decoder with the cursor button 5 orSet the color system with the cursor button 2 or To finish the main menu, press the page Back button Changing the Language Display Set the desired language with the cursor button 2 orLanguage display About language display Adjusting the Pixel Clock Adjust Tracking and Phase with the cursor buttonsButton Adjustment content Adjusting the Screen Position Adjust H. POS. and V. POS. with the cursor buttonsSelect Position with the cursor button 5 or Adjusting Picture Quality Select the item to adjust with the cursor button 5 orWhen AV signals are input When computer-related signals are input Submenu items For video system inputFor computer system input Picture menu Sets a mode which allows easy Adjustment values 0, text30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lower 30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddish Adjusting Sound Quality Adjust Treble and Bass with the cursor buttonsSelect the Sound with the cursor Button 5 or Setting and Adjusting Other Functions Options Select the item to set adjust with the cursor button 5 orFollowing optional functions can be set adjusted Select the Options with the cursor button 5 or Set adjust the desired item with the cursor button 2 or Options menu Aspect Changing Setting the Source Select a submenu item Source using the cursor button 5 orSelect the item to set using the cursor buttons 5/ or 2/3 Source item shown in text is indicated in magenta color When Auto is selected When other than Auto is selectedPress the MENU/ENTER button to set fix it Submenu item Replacing the Light-Source Lamp Loosen the two screws with a flat-end screwdriver Replace the lamp-replacement Insert the new lamp unit fully inside and fasten the screwsOpening cover and fasten Screws Resetting the Lamp Use Time Turn on the Main Power switch to go into stand-by modeProjector’s button At the same time for six seconds or more Cleaning and Replacing the Filter Turn off the Main Power switchClean the filter Reinstall the filter Troubleshooting Maintenance Specifications AV in AV in inputComputer in Computer input Other Outside dimensions DTV-format signalsTop Front Pin assignment Specifications for terminals TerminalRS-232C terminal Computer IN-1 PC / Computer OUT Terminal G1000D p.46-59 99.2.24, 552 PM English