Controls and Features | JVC G1000 instruction

Controls and Features

Front Side / Top Surface / Right Side

	1
	-
+
9	2
	2
8
7
6 5 4	3
1 Control panel	4 Adjustable foot (for adjusting upper/lower angles)

For details, refer to “Control Panel” (page 9).

2Exhaust vents

Vents for cooling fans through which warm air comes out.

CAUTION

•Do not block the exhaust vents, or heat builds up inside, possibly causing a fire. Also, do not touch the vents, or this could cause a low-temperature burn.

3Carrying handle

Raise this handle when carrying the projector.

It is adjusted to be level when shipped from the factory. Turning to extend the foot allows adjustment up to + 7°.

		+7˚
MAIN	AC IN ~
POWER
ON
OFF
	Extend	Shorten

How to use the carrying handle

Carrying handle

CAUTIONS

•When carrying the projector, do not give a shock to it. Be careful to keep its balance.

•Do not carry it while the light source lamp is on or the cooling fan is operating. This could cause personal injury.

5Built-in speaker (left)

6Built-in speaker (right)

7Lens

Projection lens, which is an electrically driven, approx. 1.5 x zoom lens. Before projection, remove the lens cap.

8Lens cap

The cap has a string attached and the string is fixed to the projector when shipped from the factory. It is recommended that the cap be fitted on to prevent the lens becoming dirty when the projector is not used.

9Remote sensor

When operating with the remote control, aim it toward this sensor. You can also operate the remote control by pointing it to a screen and allowing the remote sensor to receive the reflected light.

6

G1000 [D] p.05-14

6

99.2.24, 5:50 PM

Image 6

JVC G1000 manual Controls and Features, Front Side / Top Surface / Right Side

Contents

G1000 Safety Precautions About burning-in of the D-ILA device Lamp is turned on. Exposure of your eyes to the strong Safety PrecautionsLighters that present special hazards when over heated Xenon gas is enclosed with high pressure inside the light Contents Accessories Controls and Features Front Side / Top Surface / Right Side Connector panel AC in power input terminalMain Power switch Adjustable foot for horizontal angle adjustment Air intake area filter Refer to Precautions for Installation onBottom Surface Opening for replacing the light-source lamp Control Panel Video button Setting buttonWhen a menu is shown Computer button RS-232C terminal D-sub 9 pin Connector PanelC S video input terminal Mini DIN 4 pin Computer OUT computer output terminal D-sub 3-row 15 pin Row 15 pin Input of external sync signals is automatically detectedAudio input terminal stereo mini jack Audio audio input terminal stereo mini jack Remote Control Unit Precautions for using batteries Installing BatteriesInstall the batteries Open the back cover Do not install the projector in the following places Installing the ProjectorPrecautions for Installation When installing the projector, observe the followings Center line of the lens Projection Distance and Screen SizeProjection screen size diagonal length Projection 62.32 ft 19.0 m 328 Approx cm 495 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 65.6 ft 20.0 m 345 Approx cm 521 Effective Range and Distance of the Remote Control Unit Effective range and distance of the remote control unitUse the projector with A+B about 10 m 32.8 ft or less Video signals Connecting to Various DevicesSignals that Can Be Input to the Projector Computer signals Video devices Connecting to Video DevicesConnecting to Hi-Vision Devices Hi-Vision devices Desktop type Connecting to Other DevicesConnecting to Devices which Control the Projector To Audio OUT Read the manual which comes with each device thoroughly Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer RGB output devices To R To monitor connector Supplied Connection to MacintoshPersonal computer connection cable Remove the lens cap Connecting the Power Cord SuppliedTo use the projector To prevent fire and electric shock, observe the following When Turning On the Devices Connected to the Projector Basic Operations Turning on the PowerTurn on the Main Power switch Changes to steady on When you press Computer Adjust the screen sizeWhen you press Video Follows Adjust focus with the remote control’s Focus + Adjust focusAdjust sound volume Buttons Projector’s button To turn off video image and audio sound temporarilyTo use the quick alignment function Press once Projector button Remote control unit To display the Setting menuTo use the remote control’s Preset button To display the Main menu Press the Setting button of the projector Operating the Setting MenuMaking Basic Settings Press the Setting button to select the desired item Operating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Set the color system with the cursor button 2 or Changing the Color SystemSelect Decoder with the cursor button 5 or To finish the main menu, press the page Back button Language display Changing the Language DisplaySet the desired language with the cursor button 2 or About language display Adjusting the Pixel Clock Adjust Tracking and Phase with the cursor buttonsButton Adjustment content Adjusting the Screen Position Adjust H. POS. and V. POS. with the cursor buttonsSelect Position with the cursor button 5 or When AV signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or When computer-related signals are input For computer system input Submenu itemsFor video system input Picture menu 30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lower Sets a mode which allows easyAdjustment values 0, text 30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddish Select the Sound with the cursor Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Button 5 or Following optional functions can be set adjusted Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or Select the Options with the cursor button 5 or Set adjust the desired item with the cursor button 2 or Options menu Aspect Select the item to set using the cursor buttons 5/ or 2/3 Changing Setting the SourceSelect a submenu item Source using the cursor button 5 or Source item shown in text is indicated in magenta color Press the MENU/ENTER button to set fix it When Auto is selectedWhen other than Auto is selected Submenu item Replacing the Light-Source Lamp Loosen the two screws with a flat-end screwdriver Opening cover and fasten Replace the lamp-replacementInsert the new lamp unit fully inside and fasten the screws Screws Projector’s button Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode At the same time for six seconds or more Clean the filter Cleaning and Replacing the FilterTurn off the Main Power switch Reinstall the filter Troubleshooting Maintenance Specifications AV in AV in inputComputer in Computer input Other Top Outside dimensionsDTV-format signals Front RS-232C terminal Pin assignment Specifications for terminalsTerminal Computer IN-1 PC / Computer OUT Terminal G1000D p.46-59 99.2.24, 552 PM English