Basic Operations, Turning on the Power | JVC G1000 instruction

Basic Operations

■Projector’s buttons

	STAND BY	STAND BY indicator
		OPERATE indicator
		OPERATE button
	LAMP	2, 1
	TEMP
	EMERGENCY	MAIN POWER switch
	VIDEO	1, 2
	COMPUTER	1, 2
	COMPUTER
	SETTING

+3

QUICK

ALIGN.

-2

The following describes the basic procedure for normal use of the projector.

1.Turning on the Power

1 Turn on the MAIN POWER switch.

ON [ ❙ ]:The main power turns on and the STAND BY indicator comes on.

Projector’s indicator

STAND BY

(ON)

2Press the OPERATE button. (Or press the remote control’s OPERATE button for one second or more.)

•The OPERATE indicator comes on.

•About 30 seconds after the MAIN POWER switch is turned on, you can start projecting.

Projector

Remote control unit

OPERATE

(ON)

or

Note

•After the power is turned on, the screen may be jumbled for a few seconds, but this is not a malfunction.

■Remote control unit

■Turning off the Power

1Press the OPERATE button. (Or press the remote control’s OPERATE button for one second or more.)

OPERATE

COMPUTER VIDEO

	T
VOL.	ZOOM	FOCUS
	W
PAGE	MENU/ENTER
PAGE
BACK
PRESET
QUICK		AV
ALIGN.		MUTING

OPERATE button

2, 1

•The STAND BY indicator changes to blinking, and the projector goes into cool-down mode.

Example of the projector’s button	Projector
(ON)	(Blinking)
\	STAND BY
\

2Turn off the MAIN POWER switch after the STAND BY indicator

changes to steady on.

OFF [à]: The MAIN POWER switch turns off and the STAND BY indicator goes off.

Projector

(OFF)

STAND BY

* Do not turn off the MAIN POWER switch during cool down mode (the STAND BY indicator blinking). Turn it off after the STAND BY indicator becomes on (stand- by mode).

26

G1000[D] p.26-33

26

99.2.24, 5:51 PM

Image 26

JVC G1000 manual Basic Operations, Turning on the Power, Turn on the Main Power switch, Changes to steady on

Contents

G1000 Safety Precautions About burning-in of the D-ILA device Lamp is turned on. Exposure of your eyes to the strong Safety PrecautionsLighters that present special hazards when over heated Xenon gas is enclosed with high pressure inside the light Contents Accessories Controls and Features Front Side / Top Surface / Right Side Connector panel AC in power input terminalMain Power switch Adjustable foot for horizontal angle adjustment Air intake area filter Refer to Precautions for Installation onBottom Surface Opening for replacing the light-source lamp Control Panel Video button Setting buttonWhen a menu is shown Computer button RS-232C terminal D-sub 9 pin Connector PanelC S video input terminal Mini DIN 4 pin Computer OUT computer output terminal D-sub 3-row 15 pin Row 15 pin Input of external sync signals is automatically detectedAudio input terminal stereo mini jack Audio audio input terminal stereo mini jack Remote Control Unit Precautions for using batteries Installing BatteriesInstall the batteries Open the back cover Do not install the projector in the following places Installing the ProjectorPrecautions for Installation When installing the projector, observe the followings Center line of the lens Projection Distance and Screen SizeProjection screen size diagonal length Projection 62.32 ft 19.0 m 328 Approx cm 495 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 65.6 ft 20.0 m 345 Approx cm 521 Use the projector with A+B about 10 m 32.8 ft or less Effective Range and Distance of the Remote Control UnitEffective range and distance of the remote control unit Video signals Connecting to Various DevicesSignals that Can Be Input to the Projector Computer signals Video devices Connecting to Video DevicesConnecting to Hi-Vision Devices Hi-Vision devices Desktop type Connecting to Other DevicesConnecting to Devices which Control the Projector To Audio OUT Read the manual which comes with each device thoroughly Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer RGB output devices To R Personal computer connection cable To monitor connector SuppliedConnection to Macintosh Remove the lens cap Connecting the Power Cord SuppliedTo use the projector To prevent fire and electric shock, observe the following When Turning On the Devices Connected to the Projector Basic Operations Turning on the PowerTurn on the Main Power switch Changes to steady on When you press Computer Adjust the screen sizeWhen you press Video Follows Adjust focus with the remote control’s Focus + Adjust focusAdjust sound volume Buttons Projector’s button To turn off video image and audio sound temporarilyTo use the quick alignment function Press once Projector button Remote control unit To display the Setting menuTo use the remote control’s Preset button To display the Main menu Press the Setting button of the projector Operating the Setting MenuMaking Basic Settings Press the Setting button to select the desired item Operating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Set the color system with the cursor button 2 or Changing the Color SystemSelect Decoder with the cursor button 5 or To finish the main menu, press the page Back button Language display Changing the Language DisplaySet the desired language with the cursor button 2 or About language display Button Adjustment content Adjusting the Pixel ClockAdjust Tracking and Phase with the cursor buttons Select Position with the cursor button 5 or Adjusting the Screen PositionAdjust H. POS. and V. POS. with the cursor buttons When AV signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or When computer-related signals are input For computer system input Submenu itemsFor video system input Picture menu 30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lower Sets a mode which allows easyAdjustment values 0, text 30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddish Select the Sound with the cursor Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Button 5 or Following optional functions can be set adjusted Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or Select the Options with the cursor button 5 or Set adjust the desired item with the cursor button 2 or Options menu Aspect Select the item to set using the cursor buttons 5/ or 2/3 Changing Setting the SourceSelect a submenu item Source using the cursor button 5 or Source item shown in text is indicated in magenta color Press the MENU/ENTER button to set fix it When Auto is selectedWhen other than Auto is selected Submenu item Replacing the Light-Source Lamp Loosen the two screws with a flat-end screwdriver Opening cover and fasten Replace the lamp-replacementInsert the new lamp unit fully inside and fasten the screws Screws Projector’s button Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode At the same time for six seconds or more Clean the filter Cleaning and Replacing the FilterTurn off the Main Power switch Reinstall the filter Troubleshooting Maintenance Computer in Computer input SpecificationsAV in AV in input Other Top Outside dimensionsDTV-format signals Front RS-232C terminal Pin assignment Specifications for terminalsTerminal Computer IN-1 PC / Computer OUT Terminal G1000D p.46-59 99.2.24, 552 PM English