To turn off video image and audio sound temporarily | JVC G1000

Basic Operations (Cont.)

■ Remote control unit	For Operating Other Functions
¦

■To turn off video image and audio sound temporarily

Press the AV MUTING button.

■ Press once:

OPERATE

COMPUTER VIDEO

Video image and audio sound turn off (do not come out).

■Press again:

Video image and audio sound come out again.

	T
VOL.	ZOOM	FOCUS
	W
PAGE	MENU/ENTER
PAGE
BACK
PRESET
QUICK		AV
ALIGN.		MUTING

Remote control unit

AV

MUTING

■ To use the quick alignment function

AV MUTING button	The quick alignment function is used to automatically adjust (set)

	the screen settings of “TRACKING, PHASE, H. POS. and V. POS.”
	of computer system input video.
	• Use either the remote control’s or projector’s button.

QUICK ALIGN. button

■Projector’s button

STAND BY

LAMP

TEMP

EMERGENCY

■When using the remote control unit: Press the QUICK ALIGN. button.

■When using the projector:

Clear the menu display, and press the projector’s QUICK ALIGN. “+ 3” and “– 2” buttons at the same time.

*During the automatic adjustment, “QUICK ALIGNMENT” appears on the screen and disappears automatically after the adjustment is completed.

Remote control unit

Projector

+3

QUICK

QUICK ALIGN.

ALIGN.-2

Screen display

ENGLISH

VIDEO
COMPUTER
SETTING	Q U I C K A L I G N M E N T

+3

QUICK

ALIGN.

-2

QUICK ALIGN. buttons

Note

•This function works only for computer system inputs. It does not work for AV inputs.

CAUTION

•When performing automatic adjustment using the quick alignment function:

Use a bright, still-picture screen. It may not function correctly on a dark or motion-picture screen.

If the condition adjusted by using the quick alignment function is not good, manually adjust TRACKING, PHASE, H. POS. and V. POS. (see pages 31, 37 and 38).

29

G1000[D] p.26-33

29

99.2.24, 5:51 PM

Image 29

JVC G1000 To turn off video image and audio sound temporarily, To use the quick alignment function, Projector’s button

Contents

G1000 About burning-in of the D-ILA device Safety Precautions Lighters that present special hazards when over heated Safety PrecautionsLamp is turned on. Exposure of your eyes to the strong Xenon gas is enclosed with high pressure inside the light Contents Accessories Front Side / Top Surface / Right Side Controls and Features Main Power switch AC in power input terminalConnector panel Adjustable foot for horizontal angle adjustment Bottom Surface Refer to Precautions for Installation onAir intake area filter Opening for replacing the light-source lamp Control Panel When a menu is shown Setting buttonVideo button Computer button C S video input terminal Mini DIN 4 pin Connector PanelRS-232C terminal D-sub 9 pin Computer OUT computer output terminal D-sub 3-row 15 pin Audio input terminal stereo mini jack Input of external sync signals is automatically detectedRow 15 pin Audio audio input terminal stereo mini jack Remote Control Unit Install the batteries Installing BatteriesPrecautions for using batteries Open the back cover Precautions for Installation Installing the ProjectorDo not install the projector in the following places When installing the projector, observe the followings Projection screen size diagonal length Projection Distance and Screen SizeCenter line of the lens Projection 59.04 ft 18.0 m 311 Approx cm 469 55.76 ft 17.0 m 294 Approx cm 44362.32 ft 19.0 m 328 Approx cm 495 65.6 ft 20.0 m 345 Approx cm 521 Use the projector with A+B about 10 m 32.8 ft or less Effective Range and Distance of the Remote Control UnitEffective range and distance of the remote control unit Signals that Can Be Input to the Projector Connecting to Various DevicesVideo signals Computer signals Connecting to Hi-Vision Devices Connecting to Video DevicesVideo devices Hi-Vision devices Connecting to Devices which Control the Projector Connecting to Other DevicesDesktop type To Audio OUT Connection to an IBM PC or IBM-compatible computer Connecting to Computer DevicesRead the manual which comes with each device thoroughly RGB output devices To R Personal computer connection cable To monitor connector SuppliedConnection to Macintosh To use the projector Connecting the Power Cord SuppliedRemove the lens cap To prevent fire and electric shock, observe the following When Turning On the Devices Connected to the Projector Turn on the Main Power switch Turning on the PowerBasic Operations Changes to steady on When you press Video Adjust the screen sizeWhen you press Computer Follows Adjust sound volume Adjust focusAdjust focus with the remote control’s Focus + Buttons To use the quick alignment function To turn off video image and audio sound temporarilyProjector’s button Press once To use the remote control’s Preset button Remote control unit To display the Setting menuProjector button To display the Main menu Making Basic Settings Operating the Setting MenuPress the Setting button of the projector Press the Setting button to select the desired item Operating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Select Decoder with the cursor button 5 or Changing the Color SystemSet the color system with the cursor button 2 or To finish the main menu, press the page Back button Set the desired language with the cursor button 2 or Changing the Language DisplayLanguage display About language display Button Adjustment content Adjusting the Pixel ClockAdjust Tracking and Phase with the cursor buttons Select Position with the cursor button 5 or Adjusting the Screen PositionAdjust H. POS. and V. POS. with the cursor buttons Select the item to adjust with the cursor button 5 or Adjusting Picture QualityWhen AV signals are input When computer-related signals are input For video system input Submenu itemsFor computer system input Picture menu Adjustment values 0, text Sets a mode which allows easy30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lower 30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddish Adjust Treble and Bass with the cursor buttons Adjusting Sound QualitySelect the Sound with the cursor Button 5 or Select the item to set adjust with the cursor button 5 or Setting and Adjusting Other Functions OptionsFollowing optional functions can be set adjusted Select the Options with the cursor button 5 or Options menu Set adjust the desired item with the cursor button 2 or Aspect Select a submenu item Source using the cursor button 5 or Changing Setting the SourceSelect the item to set using the cursor buttons 5/ or 2/3 Source item shown in text is indicated in magenta color When other than Auto is selected When Auto is selectedPress the MENU/ENTER button to set fix it Submenu item Loosen the two screws with a flat-end screwdriver Replacing the Light-Source Lamp Insert the new lamp unit fully inside and fasten the screws Replace the lamp-replacementOpening cover and fasten Screws Turn on the Main Power switch to go into stand-by mode Resetting the Lamp Use TimeProjector’s button At the same time for six seconds or more Turn off the Main Power switch Cleaning and Replacing the FilterClean the filter Reinstall the filter Troubleshooting Maintenance Computer in Computer input SpecificationsAV in AV in input Other DTV-format signals Outside dimensionsTop Front Terminal Pin assignment Specifications for terminalsRS-232C terminal Computer IN-1 PC / Computer OUT Terminal G1000D p.46-59 99.2.24, 552 PM English