Ignition switch
Fuse block

ELECTRICAL CONNECTIONS

ATypical connections

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.

1Connect the colored leads of the power cord in the order specified in the illustration below.

2 Connect the antenna cord.

3 Finally connect the wiring harness to the unit.

Rear line out (see diagram

 

)

Rear ground terminal

15 A fuse

Antenna terminal

To external components (see diagram )

Black

To the metallic body or chassis of the car

Yellow *2

Red

Blue

Blue with white stripe

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

To an accessory terminal in the fuse block

To the automatic antenna if any (250 mA max.)

To the remote lead of other equipment (200 mA max.)

White with black stripe

White

Gray with black stripe

Gray

Green with black stripe

Green

Purple with black stripe

Purple

 

Left speaker (front)

Right speaker (front)

Left speaker (rear)

 

Right speaker (rear)

BConnecting the external amplifier or subwoofer

You can connect an amplifier to upgrade your car stereo system.

Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.

Remote lead

Y-connector (not supplied for this unit)

 

Remote lead (blue with white stripe)

Set “L/O MODE” to “REAR” (See page 22 of the

INSTRUCTIONS.)

Rear speakers

 

JVC Amplifier

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Set “L/O MODE” to “SUB.W” (See page 22 of the

INSTRUCTIONS.)

Subwoofer

JVC Amplifier

Signal cord (not supplied for this unit)

Front speakers

or

To the remote lead of other equipment or automatic antenna if any

CConnecting the external components

When connecting the external components, refer also to the manuals supplied for the components and adapter.

When connecting more than one component (maximum: two), it is recommended that you connect the components in series as explained below.

CAUTION:

Before connecting the external components, make sure that the unit is turned off.

You can connect the following JVC components to the CD changer jack.

JVC component

Model name

 

 

 

 

 

CD changer (CD-CH)

CH-X1500, etc.

 

You can also connect the following components through the various JVC adapters.

 

• Connection cords may need to be purchased separately.

 

 

 

 

 

Component

 

Adapter

Model name

 

 

 

 

Bluetooth device

 

Bluetooth adapter

KS-BTA200

iPod

 

Interface adapter for iPod

KS-PD100

Portable audio player with line output jacks

 

Line input adapter

KS-U57

Portable audio player with 3.5 mm stereo mini jack

AUX input adapter

KS-U58

iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

When connecting two components in series

*4

CD changer jack

AKS-BTA200

B*4 CD-CH /KS-PD100 /KS-U57 /KS-U58

To disconnect the connector

Hold the connector tightly (1), then pull it out (2).

*1

Not supplied for this unit.

*3

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint

*2

Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the power

*4

(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

 

cannot be turned on.

To use these components, set the external input setting correctly (see page 22 of the INSTRUCTIONS).

2

Page 78
Image 78
JVC GET0570-001A Typical connections, Connecting the external amplifier or subwoofer, Connecting the external components