JVC GR-D775U Power, Charging The Battery Pack, About Batteries, BATT, WARNING, power indicator, GETTING STARTED, GETTING STARTED EN, To detach the battery pack

		GETTING STARTED EN 13
Power		NOTES:
Charging The Battery Pack		● If the protective cap is attached to the battery
Charging The Battery Pack		pack, remove it ﬁrst.
POWER/CHARGE Lamp		● During charging, the camcorder cannot be
POWER/CHARGE Lamp		operated.
Battery pack		● Charging is not possible if the wrong type of
Battery pack		battery is used.
mount		battery is used.
mount		● When charging the battery pack for the ﬁrst time
		● When charging the battery pack for the ﬁrst time
		or after a long storage period, the POWER/
		CHARGE lamp may not light. In this case,
Arrow	2	remove the battery pack from the camcorder,
	2	then try charging again.
1		● If a fully charged battery pack is attached to the
1		unit, POWER/CHARGE lamp will blink for
Battery		unit, POWER/CHARGE lamp will blink for
Battery		approx. 10 seconds before it turns off.
pack		● If the battery operation time remains extremely
		● If the battery operation time remains extremely
BATT.		short even after having been fully charged, the
		battery is worn out and needs to be replaced.
Power Switch	To DC connector	Please purchase a new one.
		● Since the AC Adapter processes electricity
Lock		internally, it becomes warm during use. Be sure
Lock		to use it only in well-ventilated areas.
Button		to use it only in well-ventilated areas.
Button		● After 5 minutes have elapsed in Record-
		● After 5 minutes have elapsed in Record-
		Standby mode with the cassette inserted and no
		operation is performed, the camcorder will
		automatically turn off its power supplied from
	AC Adapter	the AC adapter. In this case, the battery charge
	AC Adapter	starts if the battery is attached to the camcorder.
To AC outlet		starts if the battery is attached to the camcorder.
To AC outlet		● Please do not pull or bend the AC adapter plug
1 Set the Power Switch to “OFF”.		● Please do not pull or bend the AC adapter plug
1 Set the Power Switch to “OFF”.		and cable. This may damage the AC adapter.
2 With the arrow on the battery pack pointing		About Batteries
upward, push the battery pack slightly against		DANGER! Do not attempt to take the batteries
the battery pack mount 1.		DANGER! Do not attempt to take the batteries
the battery pack mount 1.		apart, or expose them to ﬂame or excessive
3 Slide up the battery pack until it locks in		apart, or expose them to ﬂame or excessive
3 Slide up the battery pack until it locks in		heat, as it may cause a ﬁre or explosion.
place 2.		WARNING! Do not allow the battery or its
4 Plug the AC Adapter into an AC outlet.		terminals to come in contact with metals, as
5 Connect the AC Adapter to the camcorder.		this can result in a short circuit and possibly
5 Connect the AC Adapter to the camcorder.		start a ﬁre.
● The POWER/CHARGE lamp on the camcorder		start a ﬁre.
● The POWER/CHARGE lamp on the camcorder
blinks to indicate charging has started.		To restore the accuracy of the battery
● When the POWER/CHARGE lamp goes out,		To restore the accuracy of the battery
● When the POWER/CHARGE lamp goes out,		power indicator
charging is ﬁnished. Unplug the AC Adapter		power indicator
from the AC outlet. Disconnect the AC Adapter		If the battery power indication differs from the
from the camcorder.		actual operating time, fully charge the battery,
To detach the battery pack		and then run it down. However this method
To detach the battery pack		may not work if the battery was used for a long
Slide the battery pack downward while		may not work if the battery was used for a long
Slide the battery pack downward while		period of time under extremely high/low
pressing BATT. to detach it.		period of time under extremely high/low
pressing BATT. to detach it.		temperature condition or charged too many
		temperature condition or charged too many
Battery pack	Charging time	times.
BN-VF808U*	Approx. 1 hr. 30 min.
BN-VF815U	Approx. 2 hrs. 40 min.
BN-VF823U	Approx. 3 hrs. 50 min.
* Provided

GETTING STARTED