6INITIALSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below.

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection) – Go to "With AV Connection" on next page.

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

4

With RF Connection

 

 

 

 

ACCESS VIDEO CHANNEL SET

 

MODE

 

Hold down STOP on the recorder until the display

q

1 panel shows the following.

 

PROG.+/–

 

 

 

 

STOP 1

 

Set your TV to UHF channel 52.

 

 

 

 

 

 

 

2

SET VIDEO CHANNEL

2

TV

 

 

 

 

 

If the two vertical white bars appear clearly on the

 

 

 

 

 

 

 

 

 

 

 

 

4

screen as shown in the illustration at bottom left, go

 

 

 

 

 

 

 

to step 3.

 

 

 

 

 

 

 

If the two vertical white bars do not appear clearly,

 

 

 

 

 

 

 

 

press TV PROG.+ or to set the video recorder to a

 

 

 

 

 

 

 

 

vacant channel between 22 and 69 which is not

 

 

 

2

 

 

 

 

occupied by any local station in your area.

 

 

1

2

3

 

 

 

 

 

 

 

 

(Ex.) If channel 36 is available in your area

 

 

 

 

 

 

 

 

 

 

4

5

6

 

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

0

4

 

 

 

Then set your TV to UHF channel 36 and check if the

 

 

 

 

 

TV PROG. 2

 

two vertical white bars appear clearly on the screen; if

 

 

 

 

 

 

so, go to step 3. If not, re-set the video recorder to

 

 

 

 

 

 

another vacant channel and try again.

 

 

 

 

 

 

 

 

NOTES:

 

 

 

 

 

 

 

 

If you set the video recorder to a channel which is

 

 

 

 

 

 

 

 

occupied by a local station or has neighbouring

 

 

 

 

 

 

 

 

channels that are occupied by local stations, the

 

 

 

 

 

 

 

 

picture reception quality will be affected and some

 

 

 

 

 

 

 

 

interference noise will appear on the TV screen. Be

 

 

 

 

 

 

3

 

sure to select a vacant channel which has no

 

 

 

 

3

OK

 

broadcast on neighbouring channels.

 

 

 

 

 

If you cannot obtain the two vertical white bars

 

 

1

 

 

 

 

 

 

 

 

 

 

 

clearly with any channel between 22 and 69, consult

 

 

 

 

 

 

 

 

your JVC dealer.

 

 

 

 

 

 

 

 

EXIT VIDEO CHANNEL SET MODE

TEST SIGNAL

The channel on which the screen to

3 Press OK.

 

 

the left appear clearly in step 2 is

 

TURN OFF THE RECORDER

 

 

your Video Channel.

 

 

4 Press

.

 

 

 

 

 

 

 

To view picture signals from the video recorder, set your TV to the Video Channel.

After you finish this step, go to "Auto Set Up" on page 8.

Page 6
Image 6
JVC HR-J745EK, HR-J249EK instruction manual Video Channel Set, With RF Connection