EN21

 

 

 

 

 

 

 

ACCESS DBS RECEIVER

 

 

 

 

 

 

7

BRAND SET SCREEN

 

 

CH

 

+

Press OK.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OK

 

 

 

SET DBS RECEIVER BRAND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press the appropriate

DBS RECEIVER BRAND SET

 

 

 

 

 

 

 

NUMBER keys to enter the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 DBS Receiver Code from

4 0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the following list, then

 

 

 

 

 

 

 

 

press OK.

 

 

 

 

 

 

 

 

 

PRESS NUMBER KEY (0–9)

 

 

 

 

 

 

 

 

THEN (OK) TO TEST

 

 

 

 

 

 

 

 

PRESS (MENU) TO END

 

 

 

 

 

 

 

BRAND

CODE

 

 

 

 

 

 

 

JVC (DISH Network)

51

 

 

 

 

 

 

 

ECHOSTAR (DISH Network)

51

 

 

 

 

 

 

 

PRIMESTAR

50

 

1

2

 

3

 

 

SONY (DSS)

41

 

 

 

 

2

 

 

RCA (DSS)

40

NUMBER

4

5

 

6

 

 

After OK is pressed, the program currently received

 

 

 

 

 

 

 

7

8

 

9

 

 

 

 

 

 

through the DBS receiver will appear for about 10

 

 

0

 

 

 

 

seconds.

 

 

 

 

4

 

 

If the DBS receiver's channel changes to the channel

 

 

 

 

 

 

 

listed below for your brand of DBS receiver, setting is

 

 

 

 

 

 

 

complete. Press OK and "DBS RECEIVER CONTROL

 

 

 

 

 

 

 

IS ON" appears on the screen for about 5 seconds,

 

 

 

 

 

 

 

then it returns to the normal screen.

 

1

 

 

 

 

 

JVC [ 100

 

 

 

 

 

 

 

 

ECHOSTAR [ 100

 

 

 

 

 

 

 

 

PRIMESTAR [ 55

 

 

 

 

 

 

 

 

SONY [ 205

 

 

 

 

 

 

 

 

RCA [ 205

 

 

 

 

 

OK

 

 

If the DBS receiver's channel does not change as

 

 

 

3

 

 

shown above, press CH or TIME SCAN to

 

 

 

 

 

 

 

move the highlight bar (arrow) to "NO", then press

 

 

 

 

 

 

 

OK. Re-enter the correct code.

 

 

 

 

TIME SCAN

 

NOTES:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

It is possible that the Controller will not work with all types of

 

 

 

 

 

 

DBS receiver.

 

 

 

 

 

 

 

If your DBS receiver doesn’t respond to the code, you can’t

 

 

 

 

 

 

use the Controller to change satellite channels. In this case,

 

 

 

 

 

 

make sure to leave the DBS receiver turned on and tuned to

 

 

 

 

 

 

the proper channel before the scheduled start of timer

 

 

 

 

 

 

recording.

 

 

 

 

 

 

 

The VCR can only change the satellite channel through the

 

 

 

 

 

 

Controller during timer recording.

 

 

 

 

 

 

 

If your DBS receiver is one that can’t be operated with a

 

 

 

 

 

 

remote control (because it has no remote sensor), you can’t

 

 

 

 

 

 

use the Controller to change its channels. Make sure to leave

 

 

 

 

 

 

the DBS receiver turned on and tuned to the proper channel

 

 

 

 

 

 

before the scheduled start of timer recording.

 

 

 

 

 

 

For customers in U.S.A.: If you are unable to set the Control-

 

 

 

 

 

 

ler, please contact JVC toll free at 1-800-252-5722.

HR-S7600U-EN01-23

21

99.4.28, 2:01 PM

Page 21
Image 21
JVC HR-S7600U manual Access DBS Receiver, SET DBS Receiver Brand