46ENTIMERRECORDING(cont.)

1

2

3

 

NUMBER

"9"

4

5

6

2

 

CHECK PROGRAM DATA

 

The PlusCode number you

 

PROGRAM 1

 

entered and the matching

 

(VCR PLUS+ 12345678)

 

5 Timer-Recording informa-

 

START

STOP

 

8:00PM

= 10:00PM

 

tion is displayed on the

DATE

CH

 

Program screen. Check to

12/24/99

12 SP

 

make sure it’s accurate.

FRI

 

 

PRESS (8=DAILY, 9=WEEKLY

 

 

 

 

To change the stop time,

STOP+/– = STOP TIME, SP/EP)

 

PRESS (OK) TO END

 

press STOP +/–.

 

 

 

 

 

To timer-record daily or weekly serials, press DAILY

(NUMBER “8”) or WEEKLY (NUMBER “9”). “DAILY”

or “WEEKLY” appears on the Program screen.

NUMBER "8" 7

8

9

CANCEL

 

0

 

 

 

 

STOP+/–

 

 

 

PROG.

1

 

 

4

TIMER

Pressing the button again makes each corresponding

display disappear.

If you made a mistake, press CANCEL to access the

VCR Plus+ screen again and input the correct

PlusCode number.

If the PlusCode number you inputted is incorrect,

"ERROR" may appear on the screen to advise you of

the error. This happens when the PlusCode number is

for a program which has already passed. "ERROR" is

 

SP/EP

3

OK

ATTENTION

If there is a conflict in the timer schedule and one program overlaps with another, only the parts shown below in gray will be recorded.

Pattern 1: The program with the lower program number will be recorded.

10:00

11:00

12:00

Program 1

 

CH10

 

 

 

 

Program 2

 

 

 

 

 

 

Not recorded

 

 

CH40

 

 

 

Pattern 2: The program that is broadcast earlier will be recorded.

10:00

11:00

12:00

Program 1

 

CH10

 

 

 

 

Program 2

 

 

 

Not recorded

CH40

 

 

Pattern 3: The program that is broadcast earlier will be recorded, followed by the remaining portion of the other program.

10:00

11:00

12:00

Program 1

 

CH10

 

 

 

 

Program 2

 

 

 

 

 

CH40

Not recorded

displayed for about 5 seconds and the VCR Plus+

screen reappears.

SET TAPE SPEED

6 Press SP/EP.

RETURN TO NORMAL

SCREEN

7 Press PROG. or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears.

ENGAGE TIMER MODE

8 Press TIMER. The VCR turns off automatically and "ä" is displayed on the display panel.

IMPORTANT

If you have moved to a different area or if a broadcasting station's channel number has been changed, the wrong VCR or CABLE CH number will be displayed on the VCR Plus+ program screen in step 5. When this happens, set the correct the Guide Channel number for that station. (pg. 47, "VCR Plus+ Setup")

NOTES:

To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.

In case of a power failure after programming, the VCR’s memory backup keeps your selections for approximately 10 minutes.

When timer-recording cable channels received through a Cable Box, be sure to keep the Cable Box set to ON.

HR-S7600U-EN45-64

46

99.4.28, 2:05 PM

Page 46
Image 46
JVC HR-S7600U manual Check Program Data, Engage Timer Mode, EN Timer Recording