20ENINITIALSETTINGS(cont.)

DBS Receiver Control

Suggested Location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver's remote sensor.

Attention:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the controller so its signal reaches the remote control sensors of both the DBS receiver and cable box.

DBS receiver

Your VCR

Controller

 

(suggested locations)

 

DBS receiver

 

 

 

 

 

 

Controller

 

 

Transmitter

 

 

 

 

Connected to

Connected

 

 

 

 

 

 

to VIDEO/

 

 

ANT. IN

AUDIO IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Your VCR

CABLE

BOX

About Your DBS Receiver

This VCR has two separate methods to control your DBS Receiver.

The VCR's Wireless Remote Control Unit can control your DBS Receiver.

This eliminates the need for a separate DBS Receiver Remote Control Unit.

The VCR's Controller can also control your DBS Receiver. This allows the VCR to change your DBS Receiver's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 50. To set up the Controller go to page 21.

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) receiver and you want your VCR to change to receiver's channels during timer recording.

The VCR can control the DBS Receiver during timer recording using its Controller.

NOTES:

The Controller can automatically change the DBS Receiver channels when the VCR has been programmed using On- Screen Timer Programming (pg. 40).

Because satellite programming does not use PlusCode; the Controller can not change the DBS Receiver channels during VCR Plus+ Timer Recording.

If a cable box is used simultaneously, it is recommended to connect the DBS receiver to your VCR using A/V inputs.

Situate And Connect Controller

1

 

SITUATE CONTROLLER

 

Place the Controller so that the path between its

 

 

transmitter and the DBS receiver's remote sensor is

 

 

unobstructed.

 

 

 

2

 

ATTACH CONTROLLER

 

Fasten securely using the supplied adhesive strips.

 

 

CONNECT DBS RECEIVER

3

 

TO VCR

 

The connection method depends on the type of DBS

 

receiver you have.

 

 

 

If your DBS receiver has AUDIO and VIDEO OUT

 

 

connectors . . .

 

 

. . . connect them to the AUDIO and VIDEO IN

 

 

connectors on your VCR; if you use the input connec-

 

 

tors other than the rear panel AUDIO and VIDEO OUT

 

 

connectors, be sure to select the correct external input

 

 

mode as described in step 4, 5, 9 11 on page 46. Set

 

the VCR to channel "AU" to use the DBS receiver.

 

 

If your DBS receiver doesn’t have AUDIO and VIDEO

 

 

OUT connectors . . .

 

 

. . . connect the antenna output connector on the DBS

 

 

receiver to the ANT. IN connector on the rear of your

 

 

VCR.

 

 

Set the VCR tuner to the same channel as DBS receiver

 

 

RF output. (See page 21 also.)

 

 

NOTE:

 

 

Refer to your DBS receiver's instruction manual during

 

 

connection.

 

 

 

 

 

CONNECT CONTROLLER

4

 

TO VCR

 

Connect to the CABLE BOX connector on your VCR.

Page 20
Image 20
JVC HR-VP646U manual DBS Receiver Control, To VCR, Connect Controller, DBS receiver