JVC LVT0178-001A Activating the DSP Modes, Lamp on the button lights up, Press Surround ON/OFF so

DOLBY SURROUND

DOLBY SURROUND

English

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

Activating the DSP Modes

You can use only one DSP mode at a time. When a DSP mode is activated, another DSP mode is canceled if in use.

1. Press DSP MODE repeatedly until “THEATER” or “DIG THEATER” appears on the display.

DSP MODE

For Dolby Pro Logic, Dolby Digital, DTS Digital Surround, and MPEG Multichannel

On the front panel:

1. Press DOLBY/DTS/MPEG	DOLBY/DTS/MPEG
	SURROUND ON/OFF

•When “THEATER” is selected, the PRO LOGIC, DSP, and THEATER indicators light up on the display.

•When “DIG THEATER” is selected, the DSP and THEATER indicators light up on the display.

2. Adjust the speaker output levels.	BALANCE/SURROUND
1) Press BALANCE/SURROUND		ADJUST
ADJUST repeatedly until one of the
indications appears on the display.
“CENTER LEVEL”:
To adjust the center speaker level.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.		MULTI JOG

2)Turn MULTI JOG to adjust the selected speaker output level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

3.Adjust the center tone.

1)	Press BALANCE/SURROUND	BALANCE/SURROUND
	ADJUST repeatedly until “CENTER		ADJUST
	TONE” appears on the display.
	The display changes to show the current
2)	setting.
	Turn MULTI JOG to select the center		MULTI JOG

tone level you want.

•As you turn it, the display changes to show the following:

SOFT 2SOFT 1FLATSHARP 1SHARP 2

4. Adjust the effect level.	BALANCE/SURROUND
1) Press BALANCE/SURROUND
		ADJUST
ADJUST repeatedly until “DSP
EFFECT” appears on the display.

The display changes to show the current setting.

MULTI JOG

2)Turn MULTI JOG to select the effect level.

•As you turn it, the effect level changes as follows:

DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5 DSP EFFECT 4

As the number increases, JVC Theater Surround becomes stronger.

SURROUND ON/OFF so that the

lamp on the button lights up.

•Each time you press the button, the Dolby/ DTS/MPEG Surround turns on and off alternately.

2.Select and play a sound source.

•To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

•To enjoy MPEG Multichannel, play back a software encoded

with MPEG Multichannel and labeled with mark.

To cancel the Dolby/DTS/MPEG Surround mode

Press DOLBY/DTS/MPEG SURROUND ON/ DOLBY/DTS/MPEG

OFF again so that the lamp on the button goes	SURROUND ON/OFF
off. (“SURROUND OFF” appears on the
display.)
From the remote control:
1. Press SURROUND ON/OFF so	SURROUND
that the lamp on the DOLBY/DTS/	ON/OFF

MPEG SURROUND ON/OFF button on the front panel lights up.

•Each time you press the button, the Dolby/DTS/MPEG Surround turns on and off alternately.

•You can also turn on Dolby/DTS/MPEG Surround by pressing SURROUND MODE. (See page 22 for more details.)

2.Select and play a sound source.

•To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

•To enjoy MPEG Multichannel, play back a software encoded

with MPEG Multichannel and labeled with mark.

To cancel the Dolby/DTS/MPEG Surround mode

Press SURROUND ON/OFF again.	SURROUND
(“SURROUND OFF” appears on the display.)	ON/OFF

27