Connecting External Equipment | JVC 0802MWMMDWJEM, LVT0900-008A

Continued

To remove the speaker grilles

The speaker grilles are removable as illustrated below:

Holes Projections

Speaker grille

To remove the speaker grille, insert your fingers at the top of the speaker grille, then pull towards you. Also pull the bottom towards you.

To attach the speaker grille, put the projections of the speaker grille into the holes of the speaker.

Caution on installation

This unit is compact but high powered, so it has a built- in cooling fan which operates when the internal heat rises due to continuous use and/or high volume level. If you want to place speakers or any equipment on the sides of the unit, leave a space of at least 1 cm between the main unit and each of them to obtain sufficient cooling effect.

Connecting External Equipment

You can connect another equipment which can be used as a playback device.

When you connect and use the equipment, refer also to its manual supplied.

• DO NOT connect other equipment while the power is on.

•DO NOT plug in any equipment until all connections are complete.

To connect external equipment

Be sure that the plugs of the audio cords and the jacks on the rear of the unit are color-coded: White plugs and jacks are for left audio signals, and red ones for right audio signals.

	Right
External equipment
	Left
	R
	L
	To AUX/DVD jacks
SPEAKERS
R	L
CAUTION: R	L
SPEAKER IMPEDANCE 4~16Ω

– 8 –

Image 11

JVC 0802MWMMDWJEM manual Connecting External Equipment, To remove the speaker grilles, To connect external equipment

Contents

UX-Z7MD-Consists of CA-UXZ7MD and SP-UXZ7MD Micro Component MD SystemPage Class Laser Product Introduction Precautions Contents Main unit Location of the ButtonsMain Unit Display window Display window on the electronic swing panel Pressing one of these buttons also turns on the unit Remote Control FM antenna Connecting AntennasGetting Started Unpacking To connect an outdoor AM antenna Connecting SpeakersYou can connect the speakers using the speaker cords AM antenna Speaker grilles are removable as illustrated below Connecting External EquipmentTo remove the speaker grilles To connect external equipment R6PSUM-3/AA15F Putting the Batteries into the Remote Control Basic and Common Operations Remote control Turning On/Off the Key-touch Tone Turning On the PowerSetting the Auto Power Off To check the clock time with tones Setting the ClockTo turn off the clock indication power save mode For private listening To increase the volume, turn Volume + / control ClockwiseIf Cannot Listen appears in the main display Selecting the Sound Modes To check the sound mode currently selected, pressSound indicator goes off from the display Reinforcing the Bass Sound To change the display brightness Setting the Display IlluminationTo select the illumination color To create your favorite colors Listening to FM and AM Broadcasts Remote control Main unit To stop during searching, press ¢or 4or UP or Tuning in to a StationTo change the FM reception mode On the remote control only Press FM Mode Press SET Presetting StationsTuning in to a Preset Station Press the number buttons to select a preset number Playing Back CDs CD-R/CD-RW Playing Back the Entire CD-Normal Play Precautions on CD Playback To stop playback for a moment To go to another track directly using the number buttonsBasic CD Operations Program Play To modify the program To check the program contentsPlaying at Random-Random Play Repeating Tracks-Repeat Play Playing Back MDs To locate a particular point in a track during play Basic MD Operations On the main unit only To prohibit disc ejection About MD indicatorWhile playing or pausing On the remote control only Load an MD Press MD 3/8, then To skip the playing track, press ¢ To erase the entire program, press MD 0 to eject the MDTracks of the loaded MD will play at random Tracks are played at random To go to another group, press Group Skip Playing Tracks in a Group-Group PlayPress Group Skip or Group Skip to select a group To go to another track in the same group, press ¢ or Searching for Tracks to Play MD Title Search Playing Back Tapes To change the information shown in the main display To play both sides-Reverse modePlaying Back a Tape Listening to External Equipment Listening to External Equipment Adjusting the Audio Input LevelFor how to apply sound effects, see Recording To put a track mark manually while recording an Before You Start Recording on an MDAbout the track marks To avoid erasing important recordings To check the remaining recording time Precautions for performing long-hour stereo recordingStereo Long-Hour Recording Mdlp About High-Speed Recording To set Group recording mode Setting MD Recording ModesTo set the recording length mode To set LP-prefix addition mode To record a single track during play or pause Recording Other Sources onto an MD To keep the best recording and playback sound quality To clean the heads, capstans, and pinch rollersBefore You Start Recording on a Tape To protect your recordings To record an MD Recording onto a TapeTo record a single track of a CD/MD during play Prepare the source to record To record a disc Press MD&TAPE REC Press REV.MODE to select the reverse modeWhen recording on an MD and a tape at the same time For the tape Editing MDs Classifying the tracks on an MD Using MD Group functionsHow to make up Groups Guidance-MD Group Functions Introducing Group Editing Functions Press ¢or 4to select the last track of the new group Forming a Group-FORM GRPress SET During playback Press ¢or 4to select the first track of a new group Or Group Skip When Cannot ENTRY! appears in stepAdding a Track to a Group-ENTRY GR Press ¢or 4to select the track Function on Dividing a Group-DIVIDE GRTo join the divided groups again, see the Join GR To divide the group again, see the Divide GR function When Cannot Join appears in stepJoining Two Groups-JOIN GR Moving a Group-MOVE GR Dissolving All Groups-UNGR ALL To cancel the setting, press CancelUngrouping Tracks-UNGROUP Erasing Tracks in a Group-ERASE GR Introducing Track Editing Functions To join the divided tracks again, see the Join function Press or to precisely adjust the dividing pointDividing a Track-DIVIDE Press ¢or 4to select the track you want to divide If Cannot Join appears in step When the track belongs to a groupJoining Two Tracks-JOIN To divide the joined tracks, see the Divide function on Press ¢or 4to select the track you want to move Moving a Track-MOVE Press SET Press ¢or 4to select the track you want to erase Erasing Tracks-ERASEErasing All Tracks-ALL Erase For the disc and track title Press or to change the title entry modeAssigning Titles to an MD For the group title For the disc title Press Cancel to exit from the title entry modeRepeat steps 5 1 and 5 2 to enter other characters Press Enter to finish the current title entry Make sure that the character you want to change is flashing Changing the TitleYou can make a correction or change the title Using the Timers How Recording Timer actually works Using Recording Timer To turn on the Recording Timer again Using Daily TimerHow Daily Timer actually works To turn off the Recording Timer after its setting is done If the unit is kept turned on when the timer-on time comes To turn off the Daily Timer after its setting is doneTo turn on the Daily Timer again Volume setting appears in the main display How Sleep Timer actually works Using Sleep TimerTimer Priority Maintenance Atrac Adaptive TRansform Acoustic Coding/ATRAC3 Utoc User Table Of ContentsAdditional Information MD Disc Types MD limitations Symptoms CauseScms Serial Copy Management System Hcms High-speed Copy Management System Cannot REC x1 or x2 only CD/MD MessagesCannot REC x1 REC only Message Symptom Troubleshooting Amplifier Section-CA-UXZ7MD Specifications Victor Company of JAPAN, Limited