JVC RX-1024VBK manual Operating JVC’s Audio/Video Components

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see page 48) in addition to the connections using cables with RCA pin plugs (see page 8) or using digital cables (see page 11).

•Aim the remote control directly at the remote sensor on the receiver.

Tuner

Notes:

• If you use the buttons on the

front panel or the menu

function to choose a source,

the remote control will not

operate that source. To

operate a source with the

remote control, the source

must be selected using

After pressing FM or AM (with the remote control mode selector set to “AUDIO/TV/VCR” ), you can perform the following operations:

FM:	Selects an FM broadcast.
AM:	Selects an AM broadcast.
1 — 10, +10:	Selects a preset channel number directly.
	For channel number 5, press 5. For
	channel number 15, press +10, then 5.
	For channel number 20, press +10, then

10.

TUNING UP/TUNING DOWN:

Tunes into stations.

FM MODE/MUTE: Changes the FM reception mode.

Sound control section (Amplifier)

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR” ): SURROUND MODE: Changes the DSP modes.

After pressing SOUND (with the remote control mode selector set to “AUDIO/TV/VCR”) , you can perform the following operations:

SEA MODE:	Changes the SEA modes.
SUBWOOFER +/–:Adjusts the subwoofer output level.
CNTR +/–:	Adjusts the center speaker output
	level.
REAR•L +/–:	Adjusts the left rear speaker output
	level.
REAR•R +/–:	Adjusts the right rear speaker output level.
EFFECT:	Selects the effect level.
TEST:	Turns on or off the test tone output.
CNTR TONE:	Selects the center tone.

CD player

TV/CATV/	VCR 1				AUDIO
DBS
POWER	POWER				POWER
DVD	VCR 1		VCR 2		VIDEO
CD	TAPE/MD		PHONO		TV/DBS
AM	FM				SLEEP
SURROUND	CNTR TONE		–	CNTR		+
MODE	1		2			3	MENU
DIGITAL/	TEST		–	REAR · L		+
ANALOG
INPUT	4		5	ENTER		6
	EFFECT		–	REAR · R +
SOUND	7/P		8			9
	SEA MODE		– SUBWOOFER +
DISC	10		0			+10
	RETURN	FM MODE/				100+
			MUTE		AUDIO/
–	CHANNEL		+		TV/VCR
					CATV
					DBS
MUTE	–	VOLUME				+
ON SCREEN CONTROL
		MENU
SET						EXIT
VCR1					TAPE
	CONTROL
/REW		PLAY			FF/
DOWN	TUNING				UP
	REC
TV/VIDEO			STOP		PAUSE

LIGHT

RM-SR1024U REMOTE CONTROL

	buttons on the remote control.
•	Check to see if its remote
	control mode selector is set to
	the correct position. To
	operate audio system, TVs,
	and VCRs, set it to “AUDIO/
	TV/VCR.”
•	Refer also to the manuals
	supplied with your
	components.

Note:

After adjusting sounds, press the corresponding source selecting button or DISC to operate your target source by using 10 keys; otherwise, 10 keys cannot be used for operating your target source.

After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR” ), you can perform the following operations on a CD player:

PLAY:	Starts playing.
4:	Returns to the beginning of the current (or previous) track.
¢:	Skips to the beginning of the next track.
STOP:	Stops playing.
PAUSE:	Pauses playing. To release it, press PLAY.
1 — 10, +10:	Selects a track number directly.
	For track number 5, press 5. For track number 15, press +10, then 5. For
	track number 20, press +10, then 10. For track number 30, press +10,
	+10, then 10.

58