JVC RX-7020VBK Sound Adjustments, Attenuating the Input Signal, INPUT ANALOG/DIGITAL so, Basic

Sound Adjustments

Front Panel Remote Control

Basic

Display

		RX-7020V	AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING	FM/AM PRESET	FM MODE

STANDBY	ANALOG	SPK 1 2			BASS BOOST TUNED STEREO	AUTOMUTING SLEEP	BASS+/–
STANDBY/ON	DIGITAL AUTO	L	C	R	PROLOGIC ΙΙ DSP H.PHONE INPUT ATT	VOLUME
				CH-
MEMORY	LINEAR PCM	S.WFR LFE				MASTER VOLUME
	DIGITAL	LS	S	RS

							BASS
SURROUND ON/OFF	INPUT	BASS BOOST					BOOST
	INPUT ATT				ADJUST	SETTING
	ANALOG/DIGITAL
		DVD MULTI	DVD	VCR	TV SOUND/DBS

			SOURCE NAME
SURROUND MODE			CONTROL	SOUND
	SPEAKERS ON/OFF		DOWN UP
1	2	CDTAPE/CDR PHONO	FM/AM
		SOURCE NAME
PHONES
INPUT ATT	BASS BOOST		ADJUST

CONTROL

UP 5/DOWN ∞

A/V CONTROL RECEIVER

CATV/DBS	VCR	TV	AUDIO
DVD	DVD MULTI	CD	FM/AM
TV/DBS	VCR	TAPE/CDR	PHONO
− BASS +		−TREBLE+
SURROUND	SURROUND	ANALOG/DIGITAL	SLEEP
ON/OFF	MODE	INPUT
BASSBOOST	EFFECT	– CENTER+
	1	2	3
SOUND		MENU
	TEST	– REAR• L+
	4	5	6
		ENTER
DIMMER		– REAR• R+
	7/P	8	9
MUTING		–SUBWOOFER+
	10	0	+10
	RETURN	FMMODE	100+
CATV/DBS
CONTROL	+	+	+
TV/VIDEO	CH	TV VOL	VOLUME
	−	−	−
+
TUNING	/REW		FF/
−

REC

PAUSE

CONTROL

RM-SRX7020J REMOTE CONTROL

TREBLE+/–

SUBWOOFER +/–

Settings / Sound Adjustments

Once each of following settings has been adjusted, this receiver memorizes the adjustment for each source.

Attenuating the Input Signal	Remote
	NOT

When the input level of the analog source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion.

1 Press and hold INPUT ATT			INPUT
			ANALOG / DIGITAL
(INPUT ANALOG/DIGITAL) so			INPUT ATT
that the INPUT ATT indicator
lights up on the display.
	ANALOG SPK 1
	L C R	INPUT ATT
	S.WFR LFE
	LS S RS
	CH-

•Each time you press and hold the button, the Input Attenuator mode turns on (“INPUT ATT ON”) or off (“INPUT NORMAL”).

Note:

When selecting “DVD MULTI” as the source, this effect does not work.

Adjusting the Front Speakers	Remote
Output Balance
	NOT

If the sounds you hear from the front right and left speakers are unequal, you can adjust the speakers output balance.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1 Press ADJUST repeatedly until		ADJUST SETTIN
“BALANCE” (with the current
setting)* appears on the display.
	SPK 1
	DIGITAL AUTO L C R
	LINEAR PCM S.WFR LFE
	LS S RS
	CH-

*“CNTR (Center)” is the initial setting. If you have already changed the setting, another setting will be shown.

2 Press CONTROL UP 5/DOWN ∞ CONTROL

DOWN UP

to adjust the balance.

•Pressing CONTROL UP 5 decreases the left channel output from “CNTR” (Center) to “L–21.”

•Pressing CONTROL DOWN ∞ decreases

the right channel output from “CNTR” (Center) to “R–21.”

19