2. Press CONTROL UP 5/DOWN ° | CONTROL |
to select the appropriate digital | DOWN UP |
| |
terminal settings. |
|
•Each time you press the buttons, the display changes to show the following:
When the DGTL COAX (DIGITAL 1) is set to “DVD”
2:CD 3: TV (or DBS* ) 4: CDR Ò
2:CD 3: TV (or DBS* ) 4: MD** Ò
2:CD 3: MD** 4: CDR Ò
2:MD** 3: TV (or DBS* ) 4: CDR Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “MD” **
2:CD 3: TV (or DBS* ) 4: DVD Ò
2:CD 3: DVD 4: CDR Ò
2:DVD 3: TV (or DBS* ) 4: CDR Ò
2:CD 3: TV (or DBS* ) 4: CDR Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “CDR”
2:MD** 3: TV (or DBS* ) 4: DVD Ò
2:CD 3: TV (or DBS* ) 4: DVD Ò
2:CD 3: TV (or DBS* ) 4: MD** Ò
2:CD 3: MD** 4: DVD Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “TV” or “DBS”
2:CD 3: MD** 4: CDR Ò2: MD** 3: DVD 4: CDR Ò
2:CD 3: DVD 4: CDR Ò2: CD 3: DVD 4: MD** Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “CD”
2:DVD 3: TV (or DBS* ) 4: MD** Ò
2:DVD 3: MD** 4: CDR Ò
2:MD** 3: TV (or DBS* ) 4: CDR Ò
2:DVD 3: TV (or DBS* ) 4: CDR Ò (back to the beginning)
*If you have changed the source name from “TV” to “DBS,” “DBS” appears (see page 16).
**Change the source name to “MD” for TAPE/MD jacks when you use an MD recorder (see page 16).
Note:
When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components.
•DIGITAL 1 (coaxial): For DVD player
•DIGITAL 2 (optical): For CD player
•DIGITAL 3 (optical): For digital TV broadcast tuner
•DIGITAL 4 (optical): For CD recorder
Selecting the Analog or Digital Input
Mode
When you have connected digital source components using the digital terminals (see page 8), you need to change the input mode for these components to the appropriate digital input mode correctly — DGTL AUTO, DGTL DTS, or DGTL D.D.
Before you start, remember...
•The digital input (DIGITAL IN) terminal setting should be correctly done for the sources you want to select the digital input mode for. Without setting this digital input terminal correctly, you cannot change the input mode from analog input to digital input even if you follow the procedure below.
On the front panel:
1.Press one of the source selecting button (DVD, TV SOUND/DBS, CD, CDR, or TAPE/MD)* for which
you want to change the input mode.
The lamp on the front panel button for selected source lights up.
DVD MULTI | DVD | VCR 1 | VCR 2 | VIDEO | TV SOUND/DBS |
|
|
|
|
| SOURCE NAME |
PHONO | CD | CDR | TAPE / MD | USB AUDIO | FM / AM |
SOURCE NAME
Note:
*Among the source listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting” on page 19.)
2. Press INPUT ANALOG/DIGITAL INPUT
ANALOG/DIGITAL
(INPUT ATT) briefly to change the input mode.
•Each time you press the button, the input mode changes as follows.
DGTL AUTO 
ANALOG
(Digital)
DGTL AUTO: Select this for the digital input mode. The receiver automatically detects the incoming signal.
ANALOG: Select this for the analog input mode.
ANALOG always lights up.
When selecting “DGTL AUTO,” following indicators showing detected signals light up on the display.
LINEAR PCM
DIGITAL
:Always lights up.
:• Lights up when Linear PCM signals come in.
•The frame flashes when detecting signals.
•LINEAR PCM without frame flashes when PCM signals are not recognized.
:Lights up when Dolby Digital signals come in.
:Lights up when DTS Digital Surround signals come in.
Continued to the next page.
20
