CENTER : To adjust the center speaker output level (from
REAR L : To adjust the left rear speaker output level (from
REAR R : To adjust the right rear speaker output level (from
EFFECT : To adjust the DSP effect level. As the number increases, the effect becomes stronger (normally set it to “EFFECT 3”).
*“0” is the initial setting for the speaker output levels, and “EFFECT 3” is for the DSP effect level.
If you have already changed the setting, another setting will be shown.
5Press CONTROL 3(or 2) to make an adjustment.
•When adjusting the speaker output levels, make adjustments so that the sound level of the selected speaker is set at the
same level as that of the front speakers.
CONTROL
ANALOG | L | C | R | PRO LOGIC |
|
LPCM | SUBWFR LFE DSP |
| |||
DOLBY D | LS | S | RS | DGTL AUTO | VOL |
DTS | INPUT ATT | ||||
Ex.: When adjusting the center speaker output level
6Repeat steps 4 and 5 to make other adjustments.
To cancel Theater Surround
Press DSP MODE repeatedly until “STEREO” appears on the display. The PRO LOGIC and DSP indicators go off.
Using DAP Modes (Front Panel)
A DAP mode cannot be used with another DSP mode. Once one of the DAP modes is activated, the other DSP mode in use will be canceled.
•You have to make this adjustment for each source.
•You cannot use any DAP mode if no rear speakers are connected.
1Select and play stereo analog software or Linear PCM digital software.
2Press DSP MODE repeatedly until one of the
DAP modes appears on the display.
The DSP indicator lights up on the display.
DSP
MODE
ANALOG L | R |
SUBWFR |
| DSP | |
LS | S | RS | VOL |
3Press ADJUST.
ADJUST | The CONTROL buttons now work for sound |
| adjustments. |
4Press CONTROL ° (or 5) repeatedly until one of the following indications (with the current setting)* appears.
CONTROL
| ANALOG | L | C | R | PRO LOGIC |
|
|
|
|
|
| |
| LPCM | SUBWFR LFE DSP |
|
|
|
|
|
| ||||
| DOLBY D | LS | S | RS | DGTL AUTO |
|
|
| VOL |
| ||
| DTS | INPUT ATT |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
REAR L : To adjust the left rear speaker output level (from
REAR R : To adjust the right rear speaker output level (from
EFFECT : To adjust the DSP effect level. As the number increases, the effect becomes stronger (normally set it to “EFFECT 3”).
*“0” is the initial setting for the speaker output levels, and “EFFECT 3” is for the DSP effect level.
If you have already changed the setting, another setting will be shown.
5Press CONTROL 3(or 2) to make an adjustment.
•When adjusting the speaker output levels, make adjustments so that the sound level of the selected speaker is set at the
same level as that of the front speakers.
CONTROL
ANALOG | L | C | R | PRO LOGIC |
|
LPCM | SUBWFR LFE DSP |
| |||
DOLBY D | LS | S | RS | DGTL AUTO |
|
DTS | INPUT ATT | VOL | |||
Ex.: When adjusting the left rear speaker output level
6Repeat steps 4 and 5 to make other adjustments.
To cancel DAP Mode
Press DSP MODE repeatedly so that “STEREO” appears on the display. The DSP indicator goes off.
Creating Realistic Sound Fields
(back to the begining)
31
