Power IGN Heating Clean

VA¢ LOCK CHECK 8CI_EH

FV-SENSE E¢O LDO_W THMSTR

P-ANODE P-SW OPEN SHORT

ELECTRONIC CONTROL DISPLAY

Please check guidelines below. For your safety, water heater service should be performed only by a qualified service person.

Read the GENERAL SAFETY INFORMATION supplied by the water heater manufacturer.

CONTROL DISPLAY STATUS

"POWER" Flashing

"HEATING" and "SHORT" Flashing

"HEATING" and "OPEN" Flashing

"HEATING", "OPEN", and "SHORT" Flashing

"ECO" and "OPEN" Flashing

PROBLEM

Communication Error

The system has detected a

communication error between the upper and lower controls.

The self-diagnostic tests have found a problem with an internal circuit.

Ignition/flame failure.

The water heater has reached the maximum number of retries and is currently locked out for one hour.

Cycle the power to the water heater off and on to reset.

Weak flame sensor current.

Water temperature in the tank has exceeded 185°F (85°C) and has activated the ECO.

SOLUTION

1.Check the 5-conductor data cable that

runs between the upper and lower controls. Check that the wiring is not broken, and the connectors on both ends are properly seated in the mating connectors.

2.Replace the upper control, if the error code

does not clear - cycle power to the water heater "Off" and "On" to reset.

3.Replace the lower control if the problem persists.

1.Turn the power off for 10 to 20 seconds then on again to clear the error code.

2.If the error code persists or cannot be cleared, replace the lower control.

1.Gas supply is turned off - pressure too low. Ensure supply and manifold gas

pressures are within requirements in the installation manual. Manifold gas

pressure is non-adjustable, if pressure is off by more than 0.3" W.C. (75 Pa) replace the lower control.

2.Low supply voltage - should be 115 - 125 VAC.

3.Ensure flame sensor is making good contact with the burner flame, ensure

flame is steady.

4.Ensure the flame sensor is clean - use

ultra fine steel wool or Scotch-Brite TM pad to clean the flame sensor.

5.Ensure the hot surface ignitor is positioned to provide consistent ignition.

6.Check for any cracks in the ignitor assembly ceramic insulators - replace ignitor assembly if damaged.

7.Check resistance of the ignitor at room

temperature (77°F - 25°C) at the plug end. Replace ignitor if the resistance is not within 1.72 to 2.4 ohms at room

tem peratu re.

1.Ensure flame sensor is making good contact with the burner flame, ensure flame is steady.

2.Ensure the flame sensor is clean - use

ultra fine steel wool or Scotch-Brite TM pad to clean the flame sensor.

1.Turn the power off for 10 - 20 seconds then on again to clear this error code.

2.Replace the lower control if the error code persists.

153.33262, 153.33264 specifications

The Kenmore 153.33262 and 153.33264 are highly versatile and efficient portable air conditioners designed to provide optimal cooling solutions for indoor spaces. These models stand out in their class due to their advanced features, technologies, and user-friendly characteristics, making them suitable for a variety of environments, from small apartments to large rooms.

One of the primary features of both the Kenmore 153.33262 and 153.33264 is their high cooling capacity. With powerful BTUs, they can effectively cool spaces up to a specified square footage. This capability ensures that users can maintain a comfortable indoor climate even during the hottest summer months. Their energy efficiency is another notable aspect, allowing homeowners to enjoy cooler air without incurring exorbitant energy bills.

The two models are equipped with various modes of operation, including cooling, fan, and dehumidifying modes. This multifunctionality allows users to customize their comfort based on prevailing weather conditions. For instance, the dehumidifying mode effectively reduces excess moisture in the air, creating a more comfortable environment, particularly in humid regions.

Both air conditioners come with a user-friendly digital interface that features an easy-to-read LED display. The interface allows for straightforward adjustments to the temperature, fan speed, and operating modes. Furthermore, remote control functionality enhances convenience, enabling users to change settings from across the room.

In terms of technology, these models incorporate a self-evaporating system that minimizes the need for manual water drainage. This feature is particularly advantageous for users who prefer low-maintenance options. Additionally, both units feature a washable air filter, designed to capture dust and allergens, improving air quality and ensuring that the units operate efficiently.

Portability is another significant characteristic of the Kenmore 153.33262 and 153.33264. Built-in caster wheels and side handles allow for easy movement from room to room, making them ideal for temporary cooling needs. The easy installation process and included window exhaust kit mean users can set up the units quickly without requiring professional assistance.

In conclusion, the Kenmore 153.33262 and 153.33264 portable air conditioners offer a robust combination of high cooling performance, energy efficiency, and user-friendly features. Their advanced technologies and versatile functionalities make them an ideal choice for those seeking effective indoor air conditioning solutions.

Kenmore 153.33264, 153.33262 manual Power IGN Heating Clean

Models: 153.33262 153.33264