Manuals / Kenmore / Household Appliance / Water Heater

Kenmore 153.33264, 153.33262 Electrical Connections, Electric Shock Hazard, Solar Installation

Models: 153.33262 153.33264

1 44

Download 44 pages 3.4 Kb

Page 24

Electrical Connections

Electrical Connections

Before plugging in the water heater, always make sure:

•The Voltage and frequency correspond to that specified on the water heater.

•The electrical outlet has the proper overload fuse or breaker protection.

•Unit is to connect to a 120VAC electrical supply outlet (extension cord is not allowed).

IMPORTANT: Do not use an extension cord to connect the water heater to an electrical outlet.

•The water heater and the outlet are properly grounded.

•Installed in accordance with prevailing provisions of local codes, or in the absence of such, National Electric Code, ANSI/NFPS 70 current edition.

Completely fill the tank with water and check all connections for leaks. Open the nearest hot water faucet and let it run for three (3) minutes to purge the water lines of air and sediment and to ensure complete filling of the tank. The electrical power may then be turned on. Verify proper operation after servicing.

Electric Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Wiring Diagram

FIGURE 27.

Solar Installation

If this water heater is used as a solar storage heater or as a backup for the solar system, the water supply temperatures to the water heater tank may be in excess of 120°F. A mixing valve or other temperature limiting valve must be installed in the water supply line to limit the supply temperature to 120°F.

NOTE: Solar water heating systems can often supply water with temperatures exceeding 180°F and may result in water heater malfunction.

Air Intake

Chamber Fan	Anode

Rod

Switch

							,' Control Display
							,///
							CAUTION:
							DO NOT USE AN EXTENSION
							CORD TO CONNECT THE
	Igniter/Flame						TRANSFORMER TO AN
	Igniter/Flame						ELECTRICAL	OUTLET.
	Sense Connector						ELECTRICAL	OUTLET.
	Sense Connector
							FV
							Sensor
	CAUTION:						Power	Supply
	LABEL	ALL	WIRES	PRIOR	TO		Power	Supply
	LABEL	ALL	WIRES	PRIOR	TO		Transformer
	DISCONNECTION			WHEN	SERVICING		Transformer
	DISCONNECTION			WHEN	SERVICING
	CONTROLS.		WIRING ERRORS			CAN	CAUSE
	IMPROPER		AND	DANGEROUS		OPERATION.
	VERIFY	PROPER		OPERATION		AFTER	SERVICING.

24

Image 24

Kenmore 153.33264 Electrical Connections, Electric Shock Hazard, Disconnect power before servicing, Solar Installation

Contents

I<enmore Elite L-oaofFIRE AND EXPLOSION HAZARD IMPORTANT DEFINITIONSCan result in serious injury or death Do not store or use gasoline or otherFire or Explosion Hazard Fire HazardExplosion Hazard Breathing Hazard - Carbon Monoxide GasSAFE INSTALLATION OPERATINGYOURWATERHEATER 12 - YEAR LIMITED WARRANTY ON WATER HEATER 1 - YEAR EXCLUSIVE KENMORE LABOR WARRANTYSears Installation Service Master Protection AgreementsExcessive Weight Hazard Abbreviations Found In This Instruction ManualRECOVERY MODELINPUT MINIMUMADDITIONAL TOOLS NEEDED WHEN SWEAT SOLDERING •Wire BrushesMATERIALS NEEDED BASIC TOOLSGN,TAC GET TO KNOW YOUR WATER HEATER - GAS MODELSInstallation Checklist Water Heater LocationCombustion Air Supply and Ventilation Vent Pipe SystemoY:I =1tl Removing the Old Water HeaterMANUALGAS FIGURELocation Requirements Site LocationFIRE AND EXPLOSION HAZARD Carbon Monoxide Poisoning HazardClearances and Accessibility High Altitude InstallationPmpe_y Damage Hazard Gas Pressure Testing Gas PressureGas Requirements Gas PipingGas Pipe Capacity Table Explosion HazardExplosion Hazard atuml Gas Pipe Capacity Table Cue FtJHrUnconfined Space Confined SpaceCarbon Monoxide Warning MinimumSpaie Con,,nedAll Air from the Building Louvers and Grillestoo t%a nsulationConfinedI__L \\1 sqin.perVent Pipe Size Chimney ConnectionVertical Exhaust Gas Vent Piping Installation Temperature and Pressure Relief Valve Closed System/Thermal ExpansionPmpe y Damage Hazard Explosion HazardThe Temperature T&P Relief Valve and Pipe Insulation& Pressure Relief Valve DischargeDisconnect power before servicing Solar InstallationElectrical Connections Electric Shock HazardFO-=RYOURSAFETY READ BEFORE OPERATING manual before changing temperatureI:oo Operating InstructionsWater Heater Operation Checking the DraftBurn Hazard Water Temperature r! l =7_,I,d =I;iBurner Flames Emergency Shut DownPowered Anode Operation HOTTER JCOOLER Temperature and Pressure Relief Valve Routine Preventive MaintenanceDraining and Flushing Explosion HarzardPowerSopply ConnectorReplacement Parts Removing the Manifold/Burner AssemblyReplacing the Manifold/Burner Assembly Com;usDoor Gasket Burner iSlot ViewportReplacing the Gas Valve Thermal Expansion Tank Specifications Start Up ConditionsProperty Damage Hazard ExpansionService Safety Shut-offand Thermal SwitchOperational Conditions CondensationLeakage Checkpoints Operational Checklist PROBLEMPressurized Combustion Chamber System POSSIBLE CAUSEScontinued POWER IGN HEATING CLEAN VA¢ LOCK CHECK 8CI_EHFV-SENSEE¢O LDO_W THMSTR P-ANODE P-SWOPEN SHORT P-SW,OPEN, and CLEAN SCREEN Flashing CONTROL DISPLAY STATUSP-SWand SHORT Flashing CONTROL DISPLAY STATUS 9.FV-SENSEFlashing I...............I I COMBUSTIONFAN OFFlTURN OFFI wAI_F;L_YTP6_s_ENUMBERNO The control continually monitorsTHIS IS A REPAIR PARTS LIST, NOT A PACKING LIST _ _3 ¸KENMORE ELITE HIGH EFFICIENCY PCC Pressurized Combustion ChamberPage Sears Parts & Repair Service Center managemylife1-800-4-MY-HOME Your Home