_ii:;iiiiiii,',O_If:!!,iii;i_,!!i!iii!!ii_!i:jiOiiS:ii__!!iiiiii:,:ii :i:ii¸ili!i!!,!i:::i_,i_j
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFR
Connect to Water Line
1.Unplug refrigerator or disconnect power.
2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.
3.Locate a 1/2" (12.70 mm) to 11/4''(3.18 cm) vertical cold water pipe near the refrigerator.
IMPORTANT:
•Make sure it is a cold water pipe.
•Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.
4.Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of the
refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.
5.Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.
e
i | i¸¸ | _ii_ |
F | E | D |
A. Cold water pipe | E. Compression sleeve | |
B. Pipe clamp |
| F. Shutoff valve |
C. Copper tubing |
| G. Packing nut |
D. Compression nut |
| |
6.Fasten shutoff valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the water pipe and that washer is under the pipe clamp.
Tighten packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.
7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto the outlet end with an adjustable wrench. Do not overtighten.
8.Place the free end of the tubing into a container or sink, and turn ON main water supply and flush out the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.
Connect to Refrigerator
Style 1
1.Unplug refrigerator or disconnect power.
2.Remove and discard the shipping tape and the black, nylon plug from the gray, coiled water tubing on the rear of the refrigerator.
3.If the gray water tube supplied with the refrigerator is not long enough, a 1/4"x 1/4"coupling is needed in order to connect the water tubing to an existing household water supply line.
Thread the provided nut onto the coupling on the end of the copper tubing.
NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.
A | B | D | E | F | G |
A. Refrigerator water tubing |
| E. Ferrule | (purchased) | ||
B. Nut (provided) |
| F Nut (purchased) | |||
C. Bulb |
|
| G. Household | water line | |
D. Coupling (provided) |
|
|
|
| |
4.Turn shutoff valve ON.
5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.
Style 2
1.Unplug refrigerator or disconnect power.
2.Remove and discard the shipping tape and the black, nylon plug from the gray, coiled water tubing on the rear of the refrigerator.
3.Thread the provided nut onto the water valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.
A
B
A.Bulb
B.Nut (provided)
4.Turn shutoff valve ON.
5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.
Complete the Installation
E_ectrica_ Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can resuBt in death, fire, or electrical shock.
1.Plug into a grounded 3 prong outlet.
