Manuals / Brands / Home Audio / Speaker / Kenwood / Home Audio / Speaker

Kenwood LSF-1010 Connecting to Amp's Standard PRE-OUT Jacks

1 26

Download 26 pages, 437.31 Kb

13

LSF-1010 (EN)

DEUTSCH

FRANÇAIS ESPAÑOL

NEDERLANDS ITALIANO

Connecting to Amp's Standard PRE-OUT Jacks

Connect the PRE-OUT jacks on the amp or receiver to the LINE IN jacks

on the subwoofer. Make the connection using pin-plug audio cable.

(The cable is not included with the subwoofer.)

CAUTION

Do not plug in the power cord until you have finished mak-

ing all connections.

NotesNotes

Notes

• It is also possible to connect the subwoofer's LINE IN jacks to the REC OUT

or LINE OUT jacks on the amp or receiver (using the same cable as described

here). If you make this type of connection, however, volume adjustments at

the amp side will not affect the volume from the subwoofer. This means that

you will need to manually adjust the subwoofer volume each time you adjust

the volume at the amp side.

• If you wish to connect the subwoofer to the PRE-OUT jacks on a standalone

preamplifier, the preamp unit must include a second set of terminals for

connection to speaker amps, and must be capable of simultaneous output to

both the PRE-OUT jacks and the speaker-amp jacks.

· ª· ª

SPEAKERS

L

R

LR

PRE OUT

· ª· ª

Pin-plug audio cable (purchased separately)

PRE-OUT jacks (on amp or receiver)

Subwoofer

Making Connections

Satellite speakers

(right) (left)

Included speaker cord White stripe

Note About Pin-Plug Cables

Some commercially available pin-plug cables have relatively plug ends that

may become bent if the subwoofer is installed vertically. Bending of plugs

may cause internal wires to break, resulting in loss of sound. If installing the

subwoofer vertically, be sure to use pin-plug cables with short plugs.

Speaker cords (included)

Contents

Main Before applying power Caution : Read this section carefully to ensure safe operation. Introduction Safety precautions Caution : Read this section carefully to ensure safe operation. WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Unpacking Introduction Contents IMPORTANT SAFEGUARDS Caution : Read this page carefully to ensure safe operation. IMPORTANT SAFEGUARDS Location and Orientation Attaching the Cushions Satellite Speakers Subwoofer Location and Orientation Location Precautions Interference with AM Reception Subwoofer and Satellite Speaker Magnetic Shielding and TV Color Reception Feedback (Howling) CAUTION (SUBWOOFER only) Setting Up the Satellite Speakers 1. Attach the speaker to the arm. FIRST: Attach speaker cord. Adjusting the Speaker Angle 2. Attach the arm to the stand. Setting Up the Satellite Speakers Before Connecting... Making Connections Subwoofer 1. If your amp or receiver includes a SUBWOOFER PRE- OUT jack: 2. If your amp or receiver does not include a SUBWOOFER PRE-OUT jack: 3. If your amp or receiver includes standard PRE-OUT jacks: Connecting to Amp's SUBWOOFER PRE-OUT Jack Do not plug in the power cord until you have finished mak- ing all connections. Connecting to Amp's Speaker Output Terminals IMPORTANT Connecting to Amp's Standard PRE-OUT Jacks Note About Pin-Plug Cables Components and Their Functions Subwoofer Adjusting the Sound 1. Adjusting the Volume 2. Adjusting the Turnover Frequency Important Operating Notes Satellite Speakers Subwoofer Getting Ready to Adjust 1. Remove the screw cap covering each arm screw. Adjusting the Satellite Speaker Position 2. Loosen the two screws. Adjusting the Arm Height 3. Replace the screw caps. Adjusting the Satellite Speaker Position Adjusting the Arm Angle 2. Set the arm holders to the desired angle. 3. Insert and fasten the arm. Offset Mount Other Ways to Set Up the Satellite Speakers 2. Set the arm holder to vertical position. 3. Attach and fasten the arm. Wall Mount 2. Set the arm holders to the desired angle. 3. Attach speaker cord to the base. 4. Reattach the clip to the pole. 5. Attach and fasten the arm. 6. Mount the stand onto the wall. Clip-on Mount 2. Clamp the clip onto an appropriate object. 3. Attach and fasten the arm. Maintenance Cleaning Contact Restorers 2- 1- Troubleshooting Specifications Subwoofer Satellite speaker